Insulation of the floor in a private wooden house from below from the basement: how and with what to insulate, technology and materials

Korovin Sergey Dmitrievich

Master of Architecture, graduated from Samara State University of Architecture and Civil Engineering. 11 years of experience in design and construction.

It is important to properly insulate the floor, as this will prevent heat loss from the building and ensure the most comfortable temperature. There are two ways of insulation: from above and from below. Each case must be considered separately, since when thermal protection of different elements of a building is carried out, only one of them will be competent from the point of view of thermal engineering. When is it better to use floor insulation in a wooden house or in a country house from below?

Basic structures for insulation

Thermal protection of vertical elements in a private house is required in three cases:

insulation of the floor above a cold basement;
interfloor ceilings;
attic floor in the presence of a cold attic.

In the second case, work is carried out to improve sound insulation characteristics.

Insulation in a wooden house helps prevent the following problems:

overconsumption in the heating system;
violation of the temperature and humidity conditions of the room;
rotting of floor structures;
the appearance of mold and mildew.

In a private house or country house, it is worth thinking about carrying out thermal insulation measures at the design stage.

Calculation of approximate cost

Spraying penoizol:

Application thickness, cm	Price in rub. per cube, density 36 kg/m3	Price in rub. per cube, density 53 kg/m3
3	450	800
6	900	1550
10	1500	2600

Insulation using ready-made sheets:

Slab thickness. cm	Price in rub. for 1 m2
10	1200
15	1800
20	2300

Insulation by pouring method:

Type of work	price, rub. for 1 m3
Pouring on the object under construction or into existing holes	1500
Filling with drilling	1500+200 per hole

Insulation prices are approximate and may vary depending on the region and service provider.

As you can see, foam is not an inexpensive method of insulation, but taking into account the subsequent savings on heating and the speed of application, it is possible to reduce the overall cost of building a building. In addition, the price may be partially covered when carrying out insulation work with your own hands.

In what cases and why is insulation from below correct?

It is better to insulate the floor above a cold attic from above, but the thermal protection of the floor above the basement is technically more competent to perform from below. This has its reasons:

there is no reduction in the height of the room on the ground floor;
there is no need to choose dense rigid insulation that will withstand the loads from residents, furniture and equipment;
protection from freezing not only of the floor, but also of the entire wooden floor;
displacement of the dew point (the line on which condensation falls) to the surface of the ceiling from the thickness of the structure, which prevents rotting.

But when carrying out work in a private house or dacha, some difficulties may arise specifically related to work from below:

the need for more reliable fastening of the insulation;
the difficulty of working in low subfloor conditions;
the need to work on the ceiling leads to rapid fatigue of workers;
restrictions on types of insulation.

Therefore, if you are looking for simpler methods of insulation, we recommend that you read the following articles:

Is it possible to insulate with foam yourself?

Basically, they carry out internal thermal insulation work on their own. For this you need:

Wooden slats or metal profiles as guides for sheathing.
Foam cans and a construction gun.
Construction knife.

First, the surface in the house is cleaned of dust, flowers, and cobwebs. After this, the profiles are fixed in increments of 50 cm vertically along the wall, with horizontal jumpers of 50 cm.

Safety precautions: glasses, protective clothing, gloves.
Apply a little automotive lubricant to the construction gun for better performance.
Insert the can into the gun.
Apply foam to the surface.

Clean the gun after use. If there is any liquid left in the container, close it tightly.

Wait for complete drying - from 1 to 3 days. Then carry out the final finishing.

Before installing the sheathing, it is necessary to prepare the surface.

Cleans from dust and cobwebs.

If installation work is carried out outdoors, then remove old whitewash, swollen plaster, pieces of cement, and other protruding objects.

After cleaning, fix the guides (wooden slats or metal profiles) in increments of 50 cm. For strength, horizontal jumpers are made every 50 cm. Hardware is used depending on the surface material (anchor, dowel-nails).

All work on laying electrical cables and other communications is done before insulation begins. Electrical wires are laid in corrugation.

First, you need to fill all the cracks, joints, and cracks with material. This will get rid of voids where a cold bridge may occur. As well as voids that arise at the junction of the sheathing and the surface.

After this, spraying is done with even sweeping movements from side to side. The surface is covered from top to bottom.

While performing the work, make sure that the sheathing remains visible. The finishing coating (plasterboard, chipboard, other materials) will subsequently be fixed onto it.

Foaming of the material takes place inside the equipment. After application, hardening will occur within 15-20 minutes. Complete drying occurs in a day or three.

Experts recommend starting finishing after 5 days.

After 5 days, you need to level the surface before finishing coat. To do this, use a construction knife to cut off excess frozen foam. They do this level with the sheathing. The surface should be smooth, without depressions or bumps. If it is difficult to work with a knife, take a hacksaw with fine teeth.

Afterwards the finishing is fixed onto the prepared surface.

The surface of their foam is not covered with various types of plaster, putty, or wallpaper. For cladding use:

drywall (regular, moisture resistant);
plastic, glass wood panels;
lining;
Chipboard, fibreboard, OSB.

The material is fixed with hardware to the previously created sheathing. A waterproofing layer is not required.

Material requirements

The peculiarities of the method of carrying out work force the use of only certain thermal insulation materials. The basic requirements when carrying out heat-protection measures in a private wooden house or in a country house from below include:

small mass of insulation, since the place of attachment to the ceiling experiences increased loads;
Ease of use;
high efficiency;
structure coherence (bulk materials are not suitable);
if possible, fire resistance, since when carrying out work in a wooden house it is necessary to ensure maximum fire safety.

There are many options for materials that satisfy all these requirements.

Warm floor systems

Connoisseurs of advanced technologies will like the “warm home” system. Its execution can be very diverse. It is possible to install a warm water floor placed under a layer of thermal insulation material or screed.

Electric heated floors are simpler in terms of installation work and subsequent operation. They are supplied with everything necessary to perform installation work, and therefore can be installed on their own, even in the absence of special skills and knowledge. It is so expensive, but it works quite effectively.

Materials for bottom insulation

It is recommended to use the following as thermal insulation layers:

mineral wool produced in the form of rolls;
Styrofoam;
polyurethane foam.

Mineral wool in the form of rigid slabs can also be used; it is installed between the beams of a wooden floor in a country house or in an individual building from below so that the width of the slab is slightly greater than the clear distance between the beams. In this case, the rigid insulation will be held in place due to friction. The same applies when installing thermal protection on an attic roof.

Mineral wool insulation has the following advantages:

high efficiency;
non-flammability;
low degree of water absorption;
resistance to biological influences.

The main disadvantage of the material is that workers require reliable protection from fibers getting into the skin and lungs: gloves, overalls, masks.

You can also use inexpensive polystyrene foam in your country house and home. Its main advantage, of course, is cost, but there are others:

good thermal insulation;
low degree of water absorption;
ease of installation;
there is no need for complex tools or special clothing.

The fact that the material has low strength is not important when insulating from below, but flammability and instability to the simultaneous effects of negative temperatures and a humid environment are obvious disadvantages. The solution to the second issue can be reliable waterproofing and protection from steam. Due to its low cost, this type of material has become quite widespread.

The third insulation option was polyurethane foam. This type of thermal protection has the following positive characteristics:

ease of installation;
reliability of fastening due to penetration into cracks, irregularities and inaccessible places;
effectiveness as thermal protection;
resistance to biological influences.

More information about this type of insulation as thermal protection for structures, including floors, can be found in the article “Insulating a house with foam.”

Features of PPU

If you use the method of spraying polyurethane foam to insulate floors, the whole process will take no more than a couple of hours. The specialist will evenly spray the thermal insulation material into the space between the joists, that’s all science. The work process, although it does not seem too complicated, has many features. Installing a high-quality polyurethane foam coating in the floor area, the service life of which can be about half a century, is not an easy task.

This is due to the following nuances:

The process of polyurethane foam formation consists of the creation and logical completion of the chemical interaction between the constituent substances of the mixture. They must be mixed qualitatively in a strictly defined proportion, as a result of which a uniform foam of microscopic bubbles is formed at the output. It is applied under high pressure, which allows the resulting coating to be highly durable and chemically neutral, with excellent thermal protection.
To achieve the maximum level of thermal insulation of the surface, it is necessary to select the correct brand of mixture for the manufacture of polyurethane foam. The thickness of the spray layer is calculated individually in each individual case and depends on the materials used to cover the floor and temperature indicators.
When carrying out floor insulation work, polyurethane foam should be applied in uniform layers of small thickness. This technique will avoid the formation of voids and other flaws.

Good quality of work on thermal insulation of floors with polyurethane foam can be ensured only with a high level of qualification of the employee, availability of equipment of the necessary power and some practical experience.

Installation technology

The fastening methods for each material are different, but when installing reliable thermal protection, it is necessary to follow the order of layers, which is the same for all. When insulating from a cold basement or underground, materials for insulation and protection of the insulation are arranged in the following order:

waterproofing;
thermal insulation layer;
vapor barrier;
floor design;
floor construction.

Compliance with just this order will ensure normal temperature and humidity conditions in the house. Next, it is necessary to consider in more detail the arrangement of protective materials.

In a house with an existing wooden floor on the 1st floor, insulation from below can be done by attaching bars with a cross-section from 50x50 to 50x100 to the beams below and placing insulating material between them. After waterproofing, the resulting pie can be hemmed with boards.

Waterproofing

Cold air from the basement can fall out in the form of condensation onto the warm surface of the ceiling. The constant presence of moisture on the structure will lead to the formation of mold or mildew, and subsequently to rotting, even if the wood is treated with special compounds. In addition, condensation is very harmful to the thermal insulation layer. It can lead to increased thermal conductivity. To avoid this, a layer of waterproofing is laid on the cold air side.

Myths about the dangers of foamed plastics

Conspiracy theorists and unscrupulous advertisers of competing classes of insulation products often spread rumors about the terrible health risks caused by foamed plastics.
If you look at it without hysterics and exaggeration, polyurethane foam actually has one property that carries a potential threat.

When burned, it can form toxic volatile substances based on formaldehyde resins. During a fire, this may be an additional risk factor for those who did not have time to leave the burning premises.

During application of the foaming composition, some inert gas and other chemical compounds are also released.

However, after the foam coating has completely hardened for the entire period of its operation, no harmful emissions occur. The complete film surrounding each microcell is chemically inert and impermeable.

To summarize, we can say that the foam coating is completely safe during operation.

During application, all precautions specified in the user manual should be observed:

use only serviceable equipment;
exclude the use of open fire and high-temperature heating devices during application;
use personal protective equipment: respirator, gloves, protective overalls with a hood and thick shoes;
When working indoors, ensure ventilation
do not use the premises for people to stay in them until the composition has completely hardened (usually 24 hours.)

Of course, during the operation of foam coatings in the house, it is necessary to establish and strictly observe fire safety rules.

Material characteristics

Foam sealant has a number of special characteristics:

foam output volume. The indicator is measured in liters, determined by the consistency and amount of mass that came out of the cylinder;
adhesion level. The parameter is intended to characterize the strength of adhesion of the substance to the base. For example, with concrete, brick, wood and plastic, the level of adhesion of the product is exceptionally high. At the same time, there is practically no grip in case of contact with oily surfaces, ice and silicone;
foaming The indicator characterizes the process of boiling of foam insulation in a cylinder;
extension. The process is a chemical reaction of a substance to its environment that follows foaming;
secondary expansion. The process occurs after polymerization of the composition, and has a negative character, since high-quality products are not subject to repeated expansion or shrinkage.

Foam for floor insulation has an expansion characteristic.
When planning the insulation of floors with polyurethane foam, one should also take into account such indicators of the quality of the substance as the level of viscosity and density.

Characteristics of polyurethane foam, its pros and cons

Polyurethane foam insulation is synthesized directly on the insulated surface through the interaction of two components: polyol and polyisocyanate. The mixing process is carried out using special equipment, which makes it difficult to insulate the floor yourself.

As a result of the chemical reaction, a voluminous substance is obtained in which closed pores occupy 90-95% of the volume of the frozen foam. This gives the resulting material unique abilities:

the best thermal insulation properties among all insulation materials: thermal conductivity coefficient - 0.022-0.035 W/(m×°K);
low level of moisture absorption - 1-3%;
practically no vapor permeability - 0.02 mg/(m*h*Pa).

Other characteristics include:

density - 20-80 kg/m3;
compressive strength - 1.53-10.19 kgf/cm2;
bending strength - 3.3-19.37 kgf/cm2.

When evaluating insulation, experts cite the strengths of PPK:

high thermal insulation properties;
durability;
good adhesion with all types of building materials;
no seams;
environmental friendliness;
self-extinguishing;
light weight;
Possibility of application to the most complex geometric surfaces;
low level of water absorption;
inertness towards all substances used at the household level;
does not serve as a basis for the reproduction of microorganisms;
wide temperature range in which the insulation can be used;
versatility - used to insulate any building structure.

We cannot remain silent about the weaknesses :

intensive aging under ultraviolet rays;
lack of vapor permeability;
complex insulation technology;
lack of resistance against mice and rats;
impossibility of creating a ventilation gap;
the need to use special equipment;
high cost of thermal insulation (work together with materials);
inability to make an accurate calculation of component consumption;
the need to strictly follow all insulation instructions;
under compressive loads, thermal insulation properties are lost.

More details about polyurethane foam as insulation can be found in the article “PPU Insulation”.

The main advantages of floor insulation with foam

Thermal insulation of floors with foam in a wooden house is characterized by a number of advantages:

foam insulator has an extremely low thermal conductivity coefficient, which determines the efficiency of thermal insulation work;
there is no load on supporting structures due to the low density and light weight of the insulation;
foam for floor insulation is capable of filling any cracks and holes, therefore eliminating the risk of cold bridges;
the polymer mass is highly elastic and is not subject to deformation under the influence of external factors;
the material provides a high level of resistance to pathogenic microflora.

The fire resistance characteristics of foam floor insulation are also impressive. Product class G 1-3, ignites only upon direct contact with fire. The service life of the material is designed for 30 years.

Why insulate the floor in a wooden house?

Wooden houses with high-quality insulation of the floor surface are extremely rare. During severe frost it is very uncomfortable to be in such a room. A cold floor does not retain heat in the house, and the room cools down quickly enough.

This is due to the laws of physics, which state that colder air is at the bottom, while warm air rushes up. Due to missing thermal insulation or improperly performed work, cold bridges appear between dried boards, through which about 25% of thermal resources are lost.

After high-quality floor insulation, this problem disappears. The room becomes more comfortable and cozy. It is necessary to carry out thermal insulation not only during repair work, but also during the construction of a new wooden house.

Classification of types of polyurethane foam

Products are classified according to the following criteria.

professional foam – sprayed using special equipment. Thermal insulation of this category requires high quality work and significant costs for professional services;
semi-professional - foam for insulation is presented in cylinders, the material is intended for domestic use.

By temperature of use:

summer – temperature range of use ranging from +5°C to +35°C;
winter – can be used in conditions down to -20°C;
all-season – the operating range extends from -10°C to +30°C.

By number of components:

single-component – ready-to-use products are presented in aerosol cans;
two-component - a complex composition requires additional preparation before installation in the form of mixing the components in a special installation, applied with a construction gun.

According to the degree of flammability:

class B1 – parameter characterizes a product with high resistance to open fire;
class B2 – indicator of self-extinguishing properties;
class B3 - the composition is not heat-resistant.

Floor insulation with two-component foam

The last category includes, for example, waterproof foam, which is relevant in the design of swimming pools and bathrooms.

The principle of operation of foam insulation

The porous structure of the foam insulator provides an air layer, which ensures an extremely low thermal conductivity coefficient of the product. Liquid foam for wall insulation in cylinders is a special mass that, when reacting with air, foams. The operating principle of this category of construction products consists of the following stages:

the cellular concentrate is sprayed onto the insulated plane;
under the influence of air a chemical reaction occurs, a process of intense foaming is observed;
over a certain period of time, the foam parameters increase to the final volumes;
then polymerization of the structure occurs.

As a result of insulating the walls of the house with foam in the air gap, the insulator is a monolithic fabric without seams, which provides a high level of heat, water and sound insulation. To spray a liquid foam composition, cylinders, pneumatic equipment and other special-purpose devices are used.

Methods of insulation with material

Polyurethane foam is convenient to use for insulating the floor from above and below due to the high adhesion of the composition. So, when arranging a floor above a cold basement floor, it is recommended to insulate the floor with polyurethane foam on the basement side. The product is ideal for creating a thermal barrier on horizontal and vertical surfaces:

when arranging the facade, rigid polyurethane foam is used;
For roofing work, soft foam or liquid polyurethane foam is recommended. The material is in demand for filling niches and voids, and is used in working with structures of complex shapes;
semi-rigid polyurethane foam is used for thermal insulation of internal walls and floors in a wooden house. This composition must be combined with hydro- and vapor barrier, as it is susceptible to moisture.

Tips for use

In order for the thermal insulation layer to last long enough, it is worth taking a responsible approach to the procedure for its operation. It is necessary to regularly carry out measures to help extend the life of the floor covering and the insulation underneath. This can be achieved if:

do not walk on the floor in street shoes, the soles of which always contain dirt and small pebbles that act as an abrasive on the floor covering;
use a powerful vacuum cleaner for cleaning, helping to collect dirt from hard-to-reach places;
protect wooden flooring from direct sunlight;
try not to exceed the maximum load that can act on the floor surface.

By following these recommendations, you can significantly extend the service life of the floor surface. It does not matter what type of insulation was preferred when performing installation work. This will extend the life of the insulation and help maintain its properties.

Features of insulation application technology

The technology for installing sprayed insulation in cylinders involves the following steps:

the cylinder is equipped with a special tube or gun, having first removed the lid;
shake the composition thoroughly for at least 60 seconds;
before applying foam thermal insulation, the surface is treated with water;
The cylinder is held with the bottom up, the voids are filled to 1/3 of the volume, leaving room for expansion of the composition.

When the foam fills the entire volume of the gap, it is recommended to sprinkle the mass with water to improve the polymerization process. Curing time for foam insulation varies depending on the model and brand, and manufacturers produce products of varying quality. Surface hardening is observed within approximately 20 minutes after spraying. Correction of the mass using a cutting tool begins no earlier than after 4 hours. The full period of polymerization of foam floor insulation in cylinders requires a period of at least 24 hours.

Providing protective equipment

When applying polyurethane foam in cylinders for floor insulation, it is worth considering that the composition is poorly washed off from skin and clothing. You should work in protective clothing; it is also important to use safety glasses and gloves. Manipulations of spraying polyurethane foam with special equipment are performed using professional equipment to completely eliminate contact of the skin and mucous membranes with the substance.

When insulating a floor with foam, you need to use protective equipment

Thermal insulation of the floor by spraying

Installation of polyurethane foam when insulating floors using spraying technology involves the use of special installations. The foam insulator components are contained in separate tanks. The working composition is prepared directly on site before use. Substances enter the mixing device, are then sent to a spray gun and applied under pressure to the surface to be treated.

Features of installation of foam insulation:

a frame structure is constructed for applying spray-on thermal insulation. Experts recommend lathing depending on the nature of the area being treated. For example, for effective thermal insulation of a wall structure, it is advisable to build a wooden or metal frame with an interval between guides of 30 cm. If you plan to insulate the floor with sprayed polyurethane foam, you should create a sheathing in increments of up to 1 m;
the foam composition is applied by smoothly moving the jet over the surface to ensure uniform distribution of the mass;
when processing vertical planes, foam insulator is sprayed from the lower perimeter, gradually filling the openings upward;
When manipulating, keep the spray gun at a distance of at least 25 cm from the surface to be treated. When moving to another sector, you must release the gun trigger to block the stream.

The flooring is laid after the foam insulation has completely polymerized.

Floor insulation by pouring method

The technology involves creating monolithic thermal insulation in the floor structure by pouring foam into specially made cavities. For example, a rough plank floor is constructed on joists, and small holes are made on the surface in designated areas for pumping polyurethane foam. If thermal protection of walls is planned by pouring polyurethane foam, the cladding is performed with a technical gap between the base and the finishing material. Next, the foam composition is poured through special holes on the facing panel.

Filling is carried out on the basis of the same spraying installations, reconfiguring the equipment parameters. In a professional environment, special units are also used for pouring polyurethane foam, which determines the high-quality level of thermal insulation work. The foam substance exclusively fills all voids down to the slightest cracks, resulting in the formation of a sealed thermal barrier with high performance characteristics.

The technology for floor insulation in a wooden house depends on the location of the floor - it can be the floor of the first floor, the interfloor floor or the floor of the attic. The highest requirements for thermal insulation performance are imposed on the floor of the first floor, unless an insulated basement is provided underneath.

Insulating the floor in a wooden house from below allows you to reduce heat loss in the house, save energy during the heating season, and avoid the rooms being blown through cracks in the floor. Thermal insulation will help prevent fungus and mold from damaging the wooden floor frame.

Polyurethane foam (PPU)

Among the types of insulation existing on the construction market, polyurethane foam is considered a material with a high degree of efficiency. It has a significant list of high technical qualities.

He also has weaknesses. First of all, you need to familiarize yourself with the advantages of polyurethane foam, which are inherent in it as insulation.

Advantages of PPU

Features a high level of adhesion to any type of surface.
Qualitatively fills all existing surface defects and cavities.
Thermal insulation measures can be carried out in a short time without excessive labor costs.
When applied, it forms a monolithic coating that completely eliminates the formation of cold bridges.
The service life of this insulation is at least 35 years.
The operating temperature range is from -50 to +140 degrees Celsius.
Has extremely low thermal conductivity.
Does not support the development of fungi and mold.
Has high mechanical strength.
The material does not interact with chemicals such as acids and alkalis.
It is characterized by reduced moisture absorption rates (in the case of using polyurethane foam with a closed pore structure).
Provides high-quality insulation from extraneous sounds.

Disadvantages of polyurethane foam insulation

There are not too many negative aspects, but they do exist.

The material is subject to fairly rapid destruction when exposed to ultraviolet radiation. This type of coating should not be left in direct sunlight.
If the insulating coating is damaged, it will not be easy to restore it due to the specifics of the material application.
The method of thermal insulation by applying polyurethane foam is quite expensive. Moreover, as the volume of work decreases, the cost of applying 1 cubic meter of insulation increases.
The use of this method completely eliminates the possibility of ventilation of the insulating layer and the base underneath it.
Polyurethane foam has a high degree of flammability and, when burned, can release toxic compounds.
To work with liquid polyurethane foam, it is mandatory to use personal protective equipment, in particular, a special suit and respiratory protection.
Application of the material in rooms where the temperature level is less than - 10 degrees Celsius is not recommended.

Advantages of bottom insulation

In order to reduce labor costs and construction costs, many resort to top insulation of wooden floors. The technology consists of installing an insulating layer of rigid heat-insulating sheet material between the frame and the finishing coating. This option is suitable for construction in regions with a relatively mild climate.

But when building in a region with cold winters, it is recommended to insulate the floor on the ground floor in a private house from below for the following reasons:

the height of the premises is not “eaten up”;
it is allowed to use any type of insulation - there are no restrictions on rigidity, since the thermal insulation layer will not experience loads from furniture, people, or household appliances;
protection against freezing is provided for the entire floor frame, and not just the external flooring;
The dew point (condensation line) moves upward to the surface of the coating, due to which the base structure is protected from rotting.

Insulation of the concrete base

Insulation of concrete floors is carried out using dense and rigid materials. The optimal choice is extruded polystyrene foam (penoplex) of hard grades. The technology is simple:

the surface of the concrete subfloor is freed from the finishing coating and all intermediate layers
the insulation is laid tightly, without gaps or gaps
A protective layer of screed is poured over the insulator . Its thickness must be at least 3 cm.

The disadvantage of this method is the change in floor level. If this option is not possible for some reason, then another insulation option should be used.

Selecting a thermal insulator

Insulation of the floor from below is carried out using slab thermal insulation material - mineral wool, polystyrene foam or extruded polystyrene foam. You can also use sprayed polyurethane foam, but this requires the involvement of specialists with professional equipment.

When choosing, pay attention to the advantages and disadvantages of each material, requirements for technical characteristics, and installation features.

Mineral wool. There are several varieties of this material:

glass wool - prone to shrinkage and inconvenient to install due to the formation of harmful dust;
slag wool – contains binding substances that are released into the air and are dangerous to human health;
basalt wool is a material that is safe for health if the composition does not include binding elements (when purchasing, you should choose products from well-known manufacturers and check for a certificate).

Basalt wool is fireproof, durable, and resistant to caking. But due to the fibrous structure of mineral wool, it tends to accumulate moisture, losing its thermal insulation properties. Therefore, special attention should be paid to the quality of installation of the waterproofing and vapor barrier.

Types of foam insulation

Foam insulation may differ in its structure and composition. We can distinguish the main types of material for insulating walls and windows:

Penoizol. It contains aldehydes, which are harmful to health, although manufacturers often claim the opposite. It dries much longer than polyurethane (complete drying time can reach three days). Typically used for insulating attics, load-bearing walls and structures. Can be purchased in the form of ready-made slabs or as a liquid composition.
Ecowool and foam concrete. Can be purchased in liquid form, most often used for pouring foundations. They are practically not used when finishing facades due to their significant weight, which puts a large load on the walls. In addition, the high cost often speaks against this material.
Polyurethane foam. Suitable only for sealing seams, joints, holes, since it does not allow moisture and steam to pass through, and this is a critical point for insulating material. When interacting with air, its volume increases twenty times, while there is a minimal amount of air bubbles inside. Can be purchased in convenient small-volume containers that have a significant shelf life.
PPU or polyurethane. The most common option, which is considered the most universal. Polyurethane insulation is very effective as thermal insulation for facades. It consists of two components; they must be mixed by machine immediately before application. The foam expands thirty to forty times from its initial volume, and small balloons form inside. Due to this, high-quality insulation of the house is achieved.

First stage of installation

Insulation of a wooden floor consists of creating a multi-layer cake, the basis of which are logs or beams on which the flooring will rest. To install the structure you will need:

lumber (bars 50x50 mm or 40x40 mm, edged board);
waterproofing film;
vapor barrier membrane;
reinforced tape;
woodworking tools;
stapler with staples;
screwdriver + self-tapping screws;
sheet material for flooring (plywood, OSB boards, etc.).

All wooden elements prepared for installation are impregnated with an antiseptic and treated with a fire retardant. Or use a universal fire-bioprotective composition.

At the bottom of the joists or beams, you need to fill the skull blocks - the basis for laying the rough flooring. For flooring, edged boards are cut, and the elements are simply laid with their ends on the skull blocks - they do not need to be fastened.

Insulation foam rating

The market offers a wide range of insulation foam from various manufacturers. This makes her choice somewhat difficult.

To avoid mistakes using low-quality substances, you should pay attention to products from well-known manufacturers:

Polynor. Popular sprayed insulation based on polyurethane foam. Very easy to use and has good vapor permeability. With its help you can create a high-quality and durable thermal insulation layer. The cost of a cylinder is within 450 rubles.
Sipur. The material is lightweight, which allows it to be used for facade insulation. It easily withstands extreme temperatures. The cost of one cylinder is about 430 rubles.
Teplis is a polyurethane insulation material that is widely used for thermal insulation of apartments, industrial buildings, balconies, loggias and other structures. Made from polymer materials. It has high heat and sound insulation properties. The cost of one cylinder (1000 ml) is approximately 650 rubles.
Ecotermix. Modern popular sprayed insulation. Widely used for thermal insulation of various structures. To facilitate the application process, they began to produce it in the form of cylinders. Depending on the thickness of the layer, the cost of insulating 1 m2 will range from 470 to 1300 rubles.
Heatlok Soy. Two-component sprayed insulation having different densities. It is made from soy extract, vegetable oil, and plastic production waste. The material is securely attached to any structure, which improves its load-bearing capacity. The thermal conductivity of polyurethane foam is at a high level. The cost of insulation using such a substance will be about 400-1100 rubles. for 1 m2.

Waterproofing

Low air temperature in an uninsulated basement can lead to condensation on the warm surface of the ceiling. If moisture is constantly in contact with the wood, even high-quality treatment will not save it from fungal damage.

Condensation is also dangerous for mineral wool and loose foam - moisture entering the pores reduces the thermal insulation properties of the materials. Therefore, it is impossible to do without installing a waterproofing film material.

The waterproofing film is laid over the installed rough base. Make sure that the overlap of the canvases is at least 12 cm, and glue the joints on both sides with reinforced tape. The canvas is laid over the walls to a height of about 20 cm; it must follow the contours of the mounted structure so that thermal insulation material can be placed in the cells between the joists.

What is the best way to insulate a building with foam - from the outside or from the inside?

It is difficult to give an unambiguous answer to this, but we will try to do so. One of the varieties of liquid foam, penoizol, is used for thermal insulation of frame buildings . This material fills the air gaps between:

external and internal walls;
wall and plastic panel;
a wall and a sheet of drywall;
subfloor and floor covering.

Using polyurethane foam, slabs made of solid thermal insulation materials are fixed, and the seams between them are also filled with foam.

Some homeowners use foam to insulate the facade of their building.

Polyurethane is used to eliminate minor defects on walls.

You will get an equally good result if you insulate the walls of frame-type houses, the roof, the attic, the facade of the house, as well as the basement and lower floor with polyurethane foam.

Installation of heat insulator and vapor barrier layer

Mineral wool slabs are cut with an allowance of a couple of centimeters in length and width - then the elements will fit into the cells by surprise, without gaps. If slabs made of polystyrene foam or extruded polystyrene foam are used, they are cut as accurately as possible to size, and after installation, all interfaces of the elements with the wooden frame and among themselves are filled with polyurethane foam.

A vapor barrier is necessary to prevent moisture from penetrating into the insulation from the room. If warm steam enters a porous material, it will pass through, cooling and turning into water. This will lead to an increase in the thermal conductivity of the insulating layer and will cause rotting of the wooden joists or beams that serve as the basis of the structure.

The vapor barrier membrane is laid on top of the cells with insulation and secured around the perimeter and along the joists with staples. Next, along the joists, counter-battens are placed - wooden blocks that will serve as the base of the floor. Sheets of plywood or other sheet material are fastened staggered along the slats.

Such an insulated base is ready for waterproofing and screed (if floor tiles are to be laid) or floor installation of any finishing coating - parquet, laminate, linoleum, etc.

Preparatory work

The technology of preparatory work is influenced by the place where the polyurethane foam is sprayed, i.e. The floor is insulated with polyurethane foam from below or above the floor, as well as the type of base: wooden or concrete.

Insulation from below

When insulating the floor from the basement, ground floor or lower part of a building located on screw piles, the complex of work comes down to removing dirt and dust. Particular attention should be paid to greasy (oil) stains. They must be removed with chemical reagents. But when spraying polyurethane foam, the easiest way to do this is with a hammer drill (for a concrete floor slab) and a chisel (for wood). In both cases, the oily material is removed. If a sub-wood floor has an oil stain on the boards, they need to be replaced.

A pothole in concrete is primed with “Betonokontakt”, after which the foam will not only hide the defect, but also strengthen the damaged area, acting as a repair mortar. Rotten boards are removed from the wooden base of the floor. Other problems such as cracks, fallen knots and creaking do not affect the quality and durability of the insulation.

Insulation of a wooden floor from above

Insulation of wooden floors with polyurethane foam begins with preparing the base. It is cleared of construction debris and dusted. Boards and joists damaged by rot, mold and mildew are removed (you can ignore other defects). Waterproofing impregnation is applied over the entire surface.

Insulation of the concrete base

Insulation of the concrete base is carried out under the screed and along the joists. In the first option, preparation of the base comes down to removing dirt and dust, as well as degreasing oily areas. Open joints between slabs, cracks and chips will be filled with foam and bound.

More thorough preparation is needed when insulating along joists. In this case, the following work is performed:

the old screed is dismantled;
Construction debris and dust are removed from the surface of the base;
the passage of logs is marked;
logs are installed.

Removing the old screed. During operation, the screed becomes covered with a network of cracks, peeling, cavities and other defects appear. It is better to remove such a screed. To do this, you need to use a hammer drill, since a chisel and hammer will take several days to complete the work.

Surface cleaning. Construction debris is removed from the surface of the ceiling, after which the base is vacuumed or removed with a damp cloth. There is no need to carry out repair work - the foam will hide defects and bridge cracks.

Marking. Pre-applied markings on the base of the floor with a pencil or marker will help you install the joists correctly. The process is carried out in several stages.

Stage 1. The line of passage of the outer lags is drawn. They should be located at a distance of 5-7 cm from the wall.
Stage 2. The distance between the extreme lags is measured.
Stage 3. The value obtained during the measurement is divided into segments of 50-60 cm (this step should be between the logs).
Stage 4. Attachment lines for internal joists are drawn.

Installation of logs. Concrete joists can be installed using several methods. But at the same time, the logs are pre-cut to size and then treated with waterproofing impregnations.

1. Fixing the timber to the concrete base is carried out using U-shaped metal elements, which are attached to the floor with dowel screws. The log is inserted between the pillars of the element and screwed to it with wood screws, 2 on each side. Using a level, it is necessary to constantly monitor the horizontal position of the beam.

2. Studs are used for fastening. They can be fixed to concrete using anchors or heels. After this, a nut and washer are screwed onto them, and through holes are drilled in the joists, through which the beam is placed on a series of studs. Fixation is carried out with a nut and washer screwed on top. The mounting diagram is clearly visible in the photo. A detailed description of each step can be found in the work “Insulating the floor on the balcony.”

3. A two-layer lathing is used. The bottom row is attached to the concrete with a metal corner, and the top row to the bottom with long wood screws. To obtain a perfectly flat surface, you can use wedges.

Process nuances

First of all, this concerns safety.

Regardless of the type of foam insulation that will be used, it is necessary to wear a special protective suit. It should be made of polyethylene, since the solution will not stick to it.

Such a protective suit must have a hood, because if the solution gets on your hair, you won’t be able to clean it, you can only cut it. It is also necessary to have gloves, goggles and a special respirator that will protect the relevant areas of the body and organs.

The first involves the use of polyurethane foam from a can, and the second through an automatic material feeding machine.

When automation is used, the solution is evenly applied to the wall, and you need to move from bottom to top. This is due to the fact that it is easier to control the process of filling the space with solution. As a result, a kind of fur coat should form on the surface, made of foam and having a relief surface.

And the last, third nuance of application concerns the thickness of the layer itself. In cases where this figure exceeds 8 cm, the work must be carried out in stages. After each application, the foam must dry before applying the next layer.

Several layers are needed because after the material expands, strong pressure is exerted on the structure, which can break it. Therefore, when applying a large amount at a time, the wall frame may not withstand it and break.

Watch the video, which uses the example of a specific wall insulation to show the basic techniques for applying foam to a wall with your own hands: