If the self-diagnosis system of the Bosch washing machine displays error F17, you need to start decoding it. Externally, the malfunction is expressed as follows: you turned on the washing machine, started the program, but do not hear the sound of water filling.
Electronic models show error F17 on the display.
On models without a screen, the RPM lights blink (light up) at 800 or 1000 + the “Rinse” light.
Causes and solutions to the problem
If error code F 17 is displayed on the Bosch washing machine display, this means that the time for filling the tank has been exceeded. The fault code may appear both at the beginning of the wash cycle and before the rinse cycle.
Note! For some Bosch washing machines, error F17 is indicated as code E17.
You’ve figured out what the error means—now you need to understand how to fix it. To do this, let’s look at the reasons for the appearance:
How to correct the situation if actions did not help? Continue troubleshooting.
Adviсe
Often code e21 is a signal that the washing machine drum is overloaded . To understand whether this is true, you need to unplug the power cord from the outlet, manually drain the water, reload the drum, and start a new wash cycle.
After the cause of error e21 has been eliminated, additional steps must be taken to reset the error. How to reset the code? To do this, set the selector switch to the “Off” position, then “Spin”, hold down the drum speed switch button for a few seconds, set the selector knob to the “Drain” mode, and press the speed switch button again for a couple of seconds.
Fault localization
Your Bosch washing machine displays error F17, water does not fill, although all filters and hoses have been checked. Proceed to inspect the internal parts of the washer.
What can cause a fault code to appear:
Inlet valve
Before checking the valve, turn off the water supply and disconnect the machine from electricity.
If after replacing the valve it was possible to solve the problem and clear the error code F 17, then everything was successful.
What to do otherwise - read on.
Pressure sensor (pressostat)
The pressure sensor monitors the amount of water in the tank, after which it sends data to the control module, which starts the washing program. When the pressure switch fails, it either gives incorrect readings or does not work at all.
How to fix the problem:
Repairing the pressure switch is useless, so if it breaks, replace it immediately. A video on the topic will help you:
Control module
As mentioned above, the control unit gives commands to start washing, rinsing or spinning. If moisture enters or voltage surges, module elements may fail. Each element is responsible for a specific part in the Bosch washing machine and gives them a signal to start.
To fix the problem, inspect the control board. To repair contacts, you will need soldering, and burnt elements will have to be replaced. Additionally, inspect the wiring running from the block to the pressure switch and inlet valve.
If the insulation is damaged, the damaged wire must be replaced. Sometimes a complete replacement of the control board may be necessary.
Source of the article: https://cosmo-frost.ru/oshibki-stiralnyx-mashin/bosch/oshibka-f17-v-stiralnoj-mashine-bosh/
Error F17, E 17 in a BOSCH washing machine - what to do? | RemBytTech, How to eliminate error f17 on a washing machine.
Inlet hose clogged
After checking the operation of the water supply system, you can proceed to the next step. First you need to shut off the flow of water into the already de-energized machine. Before removing the part, it is recommended to check it for any kinks that would prevent the normal flow of water into the washer.
If everything is in order, you need to remove the inlet hose and thoroughly check it for blockages or mechanical damage. The part is made of high strength material to withstand high pressure water. However, sometimes the inlet hose wears out or becomes damaged due to mechanical stress. If a part leaks, it is recommended to replace it, since trying to seal the hose will not lead to the desired result. If the inlet hose is clogged, it should be cleaned.
Next, you can start checking the fill valve filter. It must be rinsed well and reinstalled. After this, the solenoid valve is checked.
Error E17 - when you can fix it yourself
Don't be upset if your Bosch is stuck with code F17. In half of the cases, the problem can be fixed on your own.
| Signs | What is the reason | How to fix |
| The washing machine constantly draws and drains water, and then writes error E 17. The problem occurs in recently installed machines. | Self-draining of water from the tank . Due to incorrect connection of the drain, water leaves the tank by gravity, so the machine constantly takes in water. | Carefully read the instruction manual for your machine. The hose must rise above the water level in the tank when washing. |
Did our tips not help you get rid of the error? This means you have a breakdown, and you can’t do it without the help of a repairman.
Possible faults requiring repair
We repair Bosch washing machines every day and have accumulated a huge amount of experience. Here are the most common breakdowns that cause error E17.
| Signs | Breaking | Repair or replacement | Cost* (work only) |
| The washing machine does not draw water at all or only during rinsing. Error F17 or E17 is displayed on the case. | Fill valve. It supplies water to the SMA. The valve consists of a body, a membrane and an electromagnetic coil, which opens the membrane when water is drawn in. The coil usually fails. |
*Parts are not included in the price and are paid additionally.
Can't deal with error E17 or F17 on your own? Use the services of professionals. Call the RemBytTech service:
Or submit a repair request electronically.
The technician will arrive within 24 hours, identify the cause of the error, fix the problem at home and issue a warranty for up to 2 years.
Source of the article: https://rembitteh.ru/info/stiralnie-mashini/error/bosch/f17/
Error f17 in a Bosch washing machine: what to do, How to resolve error f17 on a washing machine.
What does error F17 mean in a Bosch washing machine?
Using error code f17, the Bosch washing machine signals that there is not enough liquid in the drum to activate the program. Or the water intake is extremely slow. Naturally, this signal can also indicate a breakdown, but first of all it is recommended to check external factors that could cause such behavior. By the way, in electromechanical machines a similar problem is manifested by the burning or blinking of the rinse mode and maximum speed indicator lamps.
What does error f17 mean?
When you turn on the washing machine and for some time you do not hear the noise of water being drawn into the tank, signal f17 appears on the unit screen. Service center technicians explain this error simply - the time allotted for water collection has been exceeded.
Some consumers are sure that fault code f17 indirectly refers to the washing machine, but we recommend refraining from jumping to hasty conclusions.
Prevention measures
Problems with your Bosh washing machine that are associated with water intake from the water supply can be prevented using preventive measures.
These include:
- Organizing the correct connection of the washing machine to communications. This applies not only to the drainage system, but also to the water intake system, as well as to electricity.
- One of the factors that lead to control module burnout is power surges in the network. It is possible to prevent equipment breakdown by connecting the machine through a voltage stabilizer.
- If the water quality in the water supply is very low, it is advisable to install a filter at the entrance to the apartment. This will prevent fractions in the water from entering the washing machine and will extend the life of the equipment.
How to fix error f17
We should immediately warn you that in some modifications of washing machines (Bosch Maxx 5, Bosch Maxx 7) this error may be indicated by code E 17. We already know what this means, we just need to figure out how to correct the situation. First, let's perform actions that every consumer can do - check the supply valve, clean the filter and the hose itself.
If after this the error disappears, the problem is completely eliminated. But what to do if the signal resumes? There is only one thing left to do - continue to look for the problem. Let's move on to checking the internal elements.
Water intake valve
Before carrying out the test, turn off the water and disconnect the Bosch washing machine from the electrical network. We disconnect the hose from the inlet valve, substituting a container in advance into which the remaining water inside will drain. Remove the top cover of the washing machine and disconnect the connectors from the valve coil. We unscrew the screw, remove the valve, and inspect it for malfunction or blockage.
We install the element in the reverse order. If, when checking the car, the error code f17 clears, the problem is solved.
Pressure control sensor
This is a pressure switch that is responsible for filling the tank and sends the necessary information to the control module, after which the washing process is activated. If the sensor fails, it begins to give false readings or stops working completely. To fix the problem, remove the top panel of the Bosch washing machine, loosen the clamp, and disconnect the sensor hose.
To check the pressure switch, insert the tube and start blowing into it. If there are no characteristic clicks, the element must be replaced with a new analogue - repairing a failed sensor will not yield anything.
Control unit module
It has already been said that such a block receives a command to start the work process of washing, rinsing or spinning the laundry. If water gets on the module elements, or a voltage drop occurs in the network, the module may well fail. In this case, the Bosch washing machine faithfully issues an error signal f17.
Difficulties with the engine
A thorough check of the engine will be required to determine where the problem is occurring. If the malfunction occurs due to wear on the carbon brushes, it is enough to replace them. In case of other engine breakdowns, in most cases, the entire engine is replaced.
After fixing the problem, you will need to reset the error. To do this, turn the program switch to the “off” position and set the selector to “spin”. After this, wait for the code to appear on the control panel and hold down the drum speed switch button for a few seconds. Then set the switch to the “drain” position and hold down the speed switch key again. The appearance of a characteristic sound signal and the simultaneous turning on of all lights for a short period of time indicate a successful reset.
We managed to determine the cause of E21, but still need a part? Order from Samodelkin: inexpensive, fast delivery, guarantee.
View all engines »
View all brushes (current collectors) »
See all drive belts »
View all tachometers »
Error E17 - when you can fix it yourself
Don't be upset if your Bosch is stuck with code F17. In half of the cases, the problem can be fixed on your own.
| Signs | What is the reason | How to fix |
| The washing machine constantly draws and drains water, and then writes error E 17. The problem occurs in recently installed machines. | Self-draining of water from the tank . Due to incorrect connection of the drain, water leaves the tank by gravity, so the machine constantly takes in water. | Carefully read the instruction manual for your machine. The hose must rise above the water level in the tank when washing. |
Did our tips not help you get rid of the error? This means you have a breakdown, and you can’t do it without the help of a repairman.
