Connecting the air conditioner to the electrical network with your own hands according to the diagrams

Agree that a socket in general is not the most important decoration of a room, and therefore you should not focus on it and place it in a prominent place. Of course, the location of the outlet for the air conditioner does not greatly affect the overall interior of the room, but it should be carefully considered so as not to damage the wall in the future and not to use extension cords again.

We will tell you where to install air conditioning outlets. We will suggest the best and safest places to place a power point. The article also provides recommendations for masking sockets and cords from air conditioning equipment.

Requirements

The electrical connection diagram for an air conditioner intended for domestic use has significant differences from the installation procedure for devices for industrial and semi-industrial use. The latter are connected to a three-phase network. Household ones operate on single-phase.

Connecting the air conditioner to the electrical network is done in two main ways:

• By direct connection to the power supply system via an outlet;
• By laying a dedicated line to the electrical panel.

For household air conditioners, the latter method is practically not used. They are usually connected via a socket. Before this, a number of preparatory work is carried out in compliance with the Installation Rules and a number of other regulatory documents. To avoid mistakes, it is worth figuring out how to connect the air conditioner to the electrical network using the chosen method so that the equipment lasts long enough.

General recommendations

The electrical circuit of an air conditioner for household services differs from the connection of a three-phase device, which is used in large offices for various purposes, business centers, and supermarkets.

It must be remembered that electrical installation is carried out in accordance with the Installation Rules and relevant regulations.

Before connecting the units to the electrical network, you should carefully prepare.

To do this you should:

• carefully read the diagrams and specifications for components and materials of the device;
• inspect the existing electrical supply system, including the location and cross-section of incoming cables;
• test the intended route with a detector for the absence of internal electrical wiring and metal elements of building structures;
• analyze the composition of the walls on the surface or inside of which electrical work will be performed.

Connecting the air conditioning system is impossible if there is old aluminum wiring in the house and there is no grounding.

Direct cable laying must be carried out taking into account the following requirements:

• the distribution box, switch, socket for a household air conditioner are located in an accessible place;
• the socket is installed at a distance of at least 50 cm from the floor and grounded metal elements (batteries, water and heat supply pipes);
• The wire is laid only horizontally and vertically;
• when laying horizontally they recede:

- from the cornice 5-10 cm,

- from the ceiling - 15 cm,

— from the baseboard – 15-20 cm;

• there must be at least 10 cm between the vertically stretched wire and corners, as well as window and door openings;
• laying parallel to gas pipes is carried out at a distance of 1 m from them;
• The electrical wire is protected from heating pipes with insulation.

In addition, the following rules must be observed for connecting devices to the electrical network:

• It is strictly forbidden to connect wires by twisting. Extension is carried out using terminal blocks or bolts;
• It is not allowed to connect a wire made of aluminum and copper due to their different electrical conductivity (for a copper cable this figure is one and a half times higher).

External wiring

If the method of laying on the wall surface is chosen, then the cables are fixed every 50-60 cm with plastic clamps, which in turn are secured to the wall with screws. When using boxes in which the wire is laid, they are secured with glue or screws.

Internal wiring

Cables hidden in the wall are laid in plastic corrugated pipes, having previously made a recess (groove) of the required length. Typically, the corrugated pipe is secured inside the wall with clamps. If the depth of the groove is 2 cm or more, then it is allowed to carry out work without a corrugated pipe.

Wires must not be laid in bunches and at a distance from each other of less than 3 mm.

Device Description

Cassette-type air conditioners are classified as split systems, which, due to their greater efficiency, quickly displaced window devices that had already become familiar “from the shelves” and confidently conquered the climate control equipment market. Split systems operate on the principle of dividing the air conditioning system into two blocks:

• Interior.
• External.

This technology allows, without cluttering the space of window openings and the usable area as a whole, to ensure compliance with a comfortable temperature regime.

Thanks to the evolution of technology, it has become common to place the noise source (compressor) outside. Users were able to enjoy a favorable indoor climate without compromising their concentration.

Selecting a location

The presence of two or more units of climate control equipment requires a choice of location for each of them. Before starting installation work, you will need accompanying documentation.

Do I need permission to install an air conditioner?

Structurally, the air conditioner is a system with an indoor and outdoor unit, which is mounted on the facade.
Multi-storey building, on the basis of Art. 246 of the Civil Code is common property with the right of disposal by all owners. Installation of equipment without approval is a violation:

• the device makes noise, buzzes, disturbing the peace of the neighbors;
• condensation can damage the façade of the building or get onto the balcony below;
• the overall block blocks the view or view and windows;
• There are risks of wall cracking, wiring shorting and fire.

Based on paragraph 1 of Art. 25 LCD installation of a split system is considered as a reconstruction or re-equipment of the premises. Clause 3.5.8 of Resolution No. 170 states that it is prohibited to install an air conditioner without permission from the management company and neighbors. Consent or refusal can only be obtained after a meeting of the residents of the house.

Important! Residents of private homes can begin installation immediately after purchasing the device.

Permission is required if:

• installation work is carried out on the front part of the high-rise building;
• the user lives in a house that is valuable from a historical and cultural point of view;
• the split system is located above the pedestrian paths;
• There are no special fences on the window opening where the block is located.

Important! The management company does not have the right to remove air conditioners. Art. 330 of the Criminal Code considers such actions as arbitrariness. Dismantling of devices is carried out only by court order.

Choosing a location for the indoor unit

Installation of the internal air conditioner module is carried out with your own hands so that cold air flows do not cause discomfort. It can be placed above the head of the sofa, on the side and behind the workplace. Construction regulations define the order of location of the indoor unit:

• from the structure to the ceiling - at least 15 cm;
• from the module to the right or left wall - at least 30 cm;
• from the block to the floor - 280 cm, but for apartments on the ground floor, the external block is mounted at the same level or lower than the internal one;
• from obstacles to the movement of air flows - no less than 150 cm;

Advice! In a room with a sofa and TV, it is better to place the air conditioner above the sofa.

Where to locate the outdoor unit?

The outdoor module is placed near a window opening or on an open loggia. If the balcony is glazed, the block is placed on a fence with good load-bearing capacity or on the facade. Residents of the 1-2 floors need to determine a place for the outdoor module as far as possible from passers-by. On the 3rd or more floors, it is allowed to place the device under a window or on the side.

In a private house, the outdoor unit is placed on a wall with high load-bearing capacity. On ventilated facades, a special fastening is organized or the block is placed on the plinth.

Determining the distance between blocks

The maximum length of the intermodule route is 6 m; if it is exceeded, additional freon injection will be required. If the external and internal modules are placed at a distance of 1 m, the route should not exceed 5 m. The excess of the system is formed into a ring and placed behind the block.

Interesting to know! Manufacturers indicate different maximum distances between blocks. For Daikin equipment it is 1.5-2.5 m, for Panasonic - 3 m.

APPLICATION AREA

Ceiling-type air conditioners are universal; they are widely used for cooling air in home, office, commercial and industrial premises with an area of ​​30–150 m2. In small rooms, installations of this type are usually not used.

This air conditioning equipment is installed in the following cases:

• large premises - private living rooms, cafes, libraries, sports clubs, restaurants;
• rooms with a non-standard layout - too long corridors, halls, galleries, conference rooms;
• if the ceilings in the building are too high (from 3.5 to 4 m) - in workshops and catering establishments.

Under-ceiling climate control systems can also be used with low ceilings. Especially for these purposes, the body of some models is designed with a shallow depth - 16.5–25 cm.

Advantages and disadvantages.

Ceiling air conditioners have a number of advantages:

1. High power and good performance.
2. Small dimensions, laconic design.
3. Convenient location for people.
4. Rational distribution of air flow.
5. Constructive variety of models.

Among the disadvantages of subceiling structures are the high cost of products in this category and the technical complexity of their installation.

What is the procedure for connecting the air conditioner to the electrical network?

It should be borne in mind that if several switches are installed nearby, their performance deteriorates due to poor cooling.

In conclusion, I would like to warn all users once again: electricity does not forgive mistakes and inaccuracies, so when connecting yourself, be adequate with your skills, so that later you do not have to worry about extinguishing the wiring and repairing expensive climate control equipment.

In this case, you should be guided by the numbers of terminals and wires. After connecting both units, you should carefully check that the work was done correctly. The air conditioner can operate at different powers, so the circuit breaker should be installed on the connection line and near the outlet.

As already noted, the air conditioner cannot be installed directly above the radiators. This is done directly into the outlet. The procedure for introducing the device into the apartment’s energy system is as follows. Connecting the evaporator In principle, the method for connecting the system modules is identical, with the exception of minor nuances, so we present a detailed method for connecting the internal module, and the external one by analogy with it. In this case, the permissible current can reach 18 A.

Greeted by clothes

The AudioQuest Niagara 3000's packaging was standard and robust. Opening the double corrugated cardboard box, you find that inside there is another box of the same kind. Its contents are packed in thick film and surrounded by a shock-absorbing polyethylene foam frame - everything is simple and rational.

At first glance, the device impresses with its front panel with slightly beveled edges. On this mirror surface with a “platinum” tint, you can, if desired, take a short course in fingerprinting. To remove excess fingerprints, a microfiber cloth is included in the kit.

The box also contained a set of two corners with holes and six screws. A speck of paint was applied to each thread in advance to prevent it from unscrewing spontaneously. All this is called the Front Panel Rack Mount Kit and is useful for installing the AudioQuest Niagara 3000 in a rack.

In the middle of the front panel there is a matte imprint of the brand logo and a composition of vertical grooves. At first glance, for some reason it seemed that this was part of the display, but these are just design elements. By the way, the spectacular and extraordinary design of the AudioQuest Niagara 3000 turns out to be quite neutral - the front panel simply reflects everything around it.

As for the indication, it is represented by a pair of LEDs: the green one on the right signals that the device is turned on, and the red one on the left indicates that its protection has been turned on. Looking ahead, I will say that during the test the overload indicator did not show itself in any way - despite all our efforts.

The power switch is recessed into the front panel.
Of the controls on the front panel, there is a single switch, “recessed” into the panel so that accidental touching is excluded. However, turning on the AudioQuest Niagara 3000 requires some effort.

By the way, this pressure does not cause the body of the device to move backward: it weighs about 12 kg - that’s enough. But you can literally turn off the device with a light touch. And this is correct: after all, we have a high voltage source in front of us - if anything happens, it should turn off instantly.

The back panel also looks as expected. This is a row of seven Schuko sockets, divided into two groups: five and two. On the right is a connector for the power cable, on the left is a compact rocker switch with an absolutely standard on/off stroke.

A look from below, taken for the sake of completeness, allowed us to see four tall legs with a surface made of dense rubber, partly capable of compensating for vibrations of the durable metal case with a matte black finish.

And one more important element is the factory nameplate with a unique number protected from counterfeiting. AudioQuest strongly encourages Niagara 3000 owners to register on their website. This will make it easier to access service procedures if they are needed.

Do-it-yourself connection and connection of air conditioner interconnect cables

After installing the air conditioner, it is necessary to lay an inter-unit cable from the indoor unit to the outdoor one, and stretch another wire from the indoor unit to the electrical system terminals. The interblock cable is mainly used with 4-5 cores of different colors to prevent errors in connecting both blocks. The cross section is selected 2.5 mm2.

The essence of the connection in general terms is as follows:

• remove the front panel and the protective cover of the unit;
• stretch the cable and place it on the side of the module;
• strip the ends of the wires, insert into the terminals and tighten with screws;
• fix the cable at the outlet of the unit;
• close the module with the lid.

After connecting both units, you should carefully check that the work was done correctly. Next comes testing of the assembled circuit and a short-term start-up of the system.

Otherwise, the connection diagram for the air conditioner to the household electrical network is individual for each model, as is the case with powerful three-phase split systems. In this regard, connection details should be specified in the attached instructions.

Preventive Maintenance

Cleaning (prevention) of an air conditioner installed in a house or apartment includes the following work:

• periodic change of filters;
• cleaning elements from dust and dirt;
• diagnostics, refilling with freon;
• if problems are identified, repair or restoration.

In standard cases, maintenance is performed 1-2 times a year. Mechanical filters require monthly cleaning. You can do this yourself. First you need to remove the panel, then remove the filters and wash them thoroughly under water using dishwashing detergent. Then dry it well and put it in place, covering it with a panel.

What you need for self-installation

You probably know how much it costs to install an air conditioner by specialists. When asked where such prices come from, since the work only lasts 3 hours, they answer that the equipment is very expensive and its depreciation makes up a significant portion of the cost. This may be true, but most of this equipment may already be on the farm. The exception is a vacuum pump, but many teams do without it, since a normal one really costs a lot, and a bad one is of no use.

During installation, it is important to ensure that the blocks are installed horizontally. This requires a good construction level

Equipment

So, to install an air conditioner with your own hands you will need the following equipment:

• A hammer drill to make a hole in the outer wall into which communications are laid connecting the indoor and outdoor units.
• Drill for installing fasteners with a set of drills of different diameters.
• A pipe cutter for cutting copper pipes and a rimmer for removing burrs (you can get by with a file/nut file and sandpaper).
• Flaring machine for copper pipes.

Device for flaring pipes
For an ideal installation, a vacuum pump is needed, but usually there is nowhere to get one and on routes up to 6 meters they can do without it.

Materials

To connect and install two split system units you will need the following consumables:

• Cable for connecting power and connecting blocks. The brand and parameters of the cable depend on the manufacturer and are usually indicated in the passport in the installation instructions. Typically this is a 4-core cable with a cross-section of 2 mm2 or 2.5 mm2. The cable length is equal to the length of the route with a small margin.
• Copper thick-walled seamless pipes (not water pipes, but special ones for cooling and air conditioning systems). Pipes will need two diameters - larger and smaller. Specific numbers will be indicated in the manual, the length of each segment is equal to the length of the route plus 20-30 cm for reserve. Once again, please note that copper pipes are not for water supply, but for the refrigeration industry. They contain a different type of copper - softer, which will flare well and can provide the required tightness. Copper tubes must be transported and stored with capped edges to prevent dust from getting into them. It is very important.
  Copper pipes need special, thick-walled, seamless soft copper pipes

• Insulation for pipes made of technical rubber. Available in dark gray or black. The color does not affect the quality; it is supplied in two-meter lengths. The required length is equal to the length of the route. You need insulation for both pipe diameters - larger and smaller.
• Drainage tube. Experts advise installing a special corrugated hose with a plastic spiral inside. When installing it yourself, it is often replaced with a polypropylene pipe. The length of the drainage tube is the length of the route plus 80 cm.
• Two L-shaped brackets for mounting the outdoor unit. Their size must correspond to the dimensions of the block, and the load-bearing capacity must exceed its weight by 4-5 times. This reserve is necessary to compensate for wind and snow loads. It is advisable to buy them from companies that sell components for air conditioners. Regular brackets may not be reliable.
  Brackets for air conditioners must withstand a heavy load - 3-4 times the weight of the outdoor unit

• Bolts, anchors, dowels. The type, dimensions and quantity depend on the type of brackets and mounting plate for the indoor unit, as well as the type of walls on which the air conditioner is mounted.
• Plastic box 60*80 cm - so that the laid communications can be covered.

That's all you need to install the air conditioner yourself.

Interblock communications how to do

A hole in the wall for the passage of communications is drilled using a hammer drill with a drill with a diameter of 4-5 cm. If the interblock route includes a drainage pipe for condensate removal, then the channel must be made with a slope (5-10 degrees towards the street). It is advisable to hide the section of the route from the indoor unit to the point where it enters the wall in the wall. When gating, a lot of dust is generated, so if renovations have already been made in the room, then it is better to lay the route outside, subsequently covering it with a decorative box.

Interblock communications can be hidden in a decorative plastic casing

The inter-unit communication route includes copper freon pipes, power supply and equipment control wires, as well as a drainage pipeline (according to the rules, condensate from the indoor unit must be drained into the sewer system, but many simply drain it outside). The required length of wiring and pipelines is determined by measuring the total length of the route (plus a small margin of 30-50 cm).

To cut copper pipes, you must use a pipe cutter, not a grinder or a hacksaw, to avoid the formation of sawdust, which can subsequently lead to breakdown of the air conditioner. Before installation, the pipelines are placed in a heat-insulating shell; to prevent debris from entering, the pipeline openings are closed with plastic plugs. All components of the route are laid together, rewound with vinyl tape, after which the route is installed in place.

After laying the interblock communications, they begin to connect the wires and the freon line. The installation instructions for the air conditioner must contain a wiring diagram that must be followed during operation.

The length of the tubes is adjusted (we cut off the required size), then it is necessary to remove the burrs (we remove the chamfer using a reamer). After threading the nut, each edge of the tubes is flared by rolling. Then the edges are connected to the fittings of the indoor and outdoor units, tightening the nuts with a torque wrench (the connections must be absolutely tight).

After checking the tightness, air is removed from the line using a vacuum pump; a manometric manifold makes it possible to control the pressure

Having finished connecting the route, check the tightness of the line and “vacuum” it (remove moisture and air) using a vacuum pump. To do this, a vacuum pump is connected to the service port of the outdoor unit through a manometric manifold, which, by pumping air out of the system, creates a vacuum in it. This process lasts about 20 minutes (depending on the volume of the circuit). After turning off the pump, observe the change in pressure for half an hour; if the pressure gauge needle does not deviate, then the system is sealed. Only after a thorough check of the tightness is it possible to open the taps of the outdoor unit and fill the circuit with freon

Attention, a freon leak can cause a compressor breakdown, but more important is the extremely harmful effect of freon on the human body

So, the system is assembled and filled with refrigerant, all that remains is to connect the air conditioner to the electrical network and check its operation. The connection diagram for the air conditioner is simple; in most household split systems, the power supply is connected to the indoor unit; to do this, you just need to connect an outlet to it.

Now you have a general idea of ​​how to install an air conditioner yourself. We were talking about installing a split system as the most efficient type of household air conditioners. The video instructions below will help you figure out how to install an air conditioner.

Installation of a mobile air conditioner does not require the intervention of highly qualified specialists: you just need to place the device within 2 m from the window (to remove hot air), and then connect it to the network.

Connecting the air conditioning system

• the connection point is connected directly to the junction box. In this situation, they do without a socket and plug. But with this connection method, it should be taken into account that the electrical wiring used must withstand the load during the simultaneous operation of all household devices connected to it. The distribution panel is additionally equipped with a system that controls automatic shutdown in case of overload;
• If an air conditioning device is installed during general repair work, a closed structure is most often used during installation. A special channel is installed in the wall. It houses the cable. One end is connected to the distribution panel, and the other is secured to the outlet terminal. At the final stage, the channel is sealed. At the same time, the interior of the room does not deteriorate. The wiring is not influenced by external negative factors;
• Installation of the socket under the air conditioner can be done in an open way. This method is used if the repairs have already been completed and residents do not want to further damage the wall. One of the ends of the wiring is connected to the junction box. A socket is connected to the other end. The cable is located on the surface of the wall covering. It is placed in a decorative box.

Advantages

Built-in air conditioners have a special set of obvious advantages:

• Easy access simplifies repairs and servicing
• Uniform distribution of flows creates a comfortable mode
• Good power, high performance, reduced noise
• Simplicity, ease of use
• Doesn't take up much space

Based on the information presented, it becomes clear that ceiling-mounted climate control systems have many clear advantages without any disadvantages.

What kind of socket is needed for an air conditioner?

The main selection parameter is the rated load when connecting.
It is recommended to buy a model with a power reserve of at least 10%. Rated voltage 220 V, 16 A. According to the installation method, models can be external, overhead or hidden. The first ones are mounted on the wall surface. They are rarely used if it is not possible to make grooves. Overheads are similar in design, but are designed to connect to wiring coming out of the wall. Can be used as temporary or when it is impossible to form a recess for hidden installation.

Hidden - the most common models. Most of the body is located in a wall niche, the front part protrudes slightly flush. Installation is more complicated than the two described above, but these models have a better design and fit into the interior of an office or apartment.

Additional characteristics:

• must be connected to grounding;
• protection class – IP54;
• connection type – F or C.

The last parameter depends on the design of the plug (plug). If the air conditioner was produced for the countries of America, Asia, Great Britain or Switzerland, it is recommended to replace the plug with a standard European one. An alternative is to purchase adapters for your specific model.

Type “C” models are gradually going out of sale because they do not have a grounding function. To power a split unit, you need to buy “F” type models.

The mechanism for introducing the device into an existing power system

The specifics of how to connect an air conditioner to the electrical network have its own technical features.

The best solution to this problem is to connect a temperature-regulating device to a separate machine in the control panel. The amperage of the latter is selected based on the technical characteristics of the equipment, calculated using the following formula: the power of the air conditioner is divided by 220V voltage, the resulting number is increased by 30% (as a reserve).

Before you carry out the procedure for connecting the cooling system, you should correctly select the required wire cross-section. This is done this way:

• for current less than 18A, the cross-section should be 1.5 mm2
• 18-25A – 2.5mm2.

The procedure for introducing the device into the apartment’s energy system is as follows. The power line itself is drawn as close as possible from the distributor to the air conditioner. You should take care of the safety of others by laying wires either through a deep recess in the wall or by constructing a protective box. This will prevent unauthorized people from accessing bare, unprotected wires. The cable is secured using special clamps. In addition to the protective option, the box also performs an aesthetic function - it does not allow the prying eye to notice the wires.

The air conditioner housing is equipped with colored wires brought out from the outside, which are connected to the corresponding terminals.

It is best to install the device during repair work. The bottom line is that it is at this time that installers are required to ditch the wall in order to lay communication lines. In the apartment, the unit is placed in such a way that the cooled air is evenly distributed throughout the room.

Any kind of split system is designed from two blocks:

1. external (attached to the wall from the outside)
2. internal (located in the room itself)

The installation of the system is carried out in the following natural order:

1. it is necessary to make a hole in the wall through which the condensate formed during the air cooling process will drain
2. the external unit is securely fixed using brackets on the street part of the house
3. the indoor unit is installed in the apartment
4. the freon line connects both parts of the device to each other
5. laying electrical wires
6. the pipe with freon should be evacuated using a pump in order to reduce the overall load on the motor, as well as remove excess air from the system

What not to do

Let us emphasize what basic requirements exist when installing an air conditioning device in a room:

• do not place the device next to large furniture - it will interfere with the correct movement of air flow
• negative decision - the location of the air conditioner is connected with the localization plane of a large number of people
• cold air should not be directed directly at a person - this will provoke the occurrence of colds

• You should not install the device above constantly operating heating appliances - it will wear out, which will negatively affect its service life
• The device also cannot be mounted in places with high-frequency operating devices - the commands and settings of the processor responsible for the operation of the cooling system may be lost
• do not install the device in areas with a difficult air circulation system, otherwise the required air temperature in the room will not be maintained: pushing off from an artificial obstacle, the air will return to the air conditioner, the automation of which will decide that the necessary thermal conditions have been achieved and will simply turn off the device
• The indoor unit of the climate control unit should be installed as level as possible so that the condensate flows through the tube into the street and does not drip onto the floor of the apartment
• if there is a canopy over the external structure, you should make sure that it is not an obstacle to the removal of exhaust air from the system

In general, there are three basic schemes for introducing an air conditioner into the electrical network. Which one to choose should be decided situationally, based on the living conditions of a particular room.

Please note that installing the device yourself and connecting it to power may negatively affect the functioning of the entire system. Sometimes it is better to spend a small amount and invite a specialist to at least consult with him about the installation process.

Guided by the recommendations given in the article, you can carry out competent installation of a climate control system in a residential area, correctly connect it to the electrical network, and also extend its service life for many years.

Flaring of copper tubes

We move on to the stage of preparing the tubes.

Error No. 5 You can cut them only with a special pipe cutter, no hacksaws or grinders!

When making a cut, it is necessary to hold the end of the copper pipe strictly downward in order to prevent any chips from getting inside.

The ends are processed with a rimmer.

Use the rimmer carefully to avoid scratching the skirt. The quality of rolling is one of the most important aspects in installing an air conditioner.

Flaring is carried out using a special tool with an eccentric. Don't forget to put the connecting nut on the tube before this step!

The width of the flare should be such that the connection eventually fits freely and unhindered into the nut.

The height of installation of the tube in the rolling clamp is strictly regulated.

The simplest and most proven old-fashioned way to determine the quality of rolling, at least at the initial stage, is to see your reflection in the “skirt”.

Flaring of the pipes of the outdoor unit will have to be done outdoors on weight. Otherwise, the line simply will not fit through the hole.

Error No. 7 Please note - if the installation does not take place on a hot, warm day, then when bringing copper pipes home from the street, close their ends and be sure to wait time for the copper to reach room temperature.

If you bring them in cold and open, then due to the dew point effect, condensation will form inside the tube, which, on a poorly evacuated air conditioner, can lead to dire consequences.

Types of brackets

Brackets for stable mounting of air conditioners have horizontal elements on which the installed unit is placed and secured against spontaneous displacement, and vertical parts that are pressed tightly against the wall. For ease of fastening, holes are provided.
In most cases, the brackets take the form of L-shaped parts, used in pairs. The differences usually relate to the shape of the profiles used in the manufacture and the presence of additional elements intended to strengthen the structure.

Important! The production of brackets used outdoors uses stainless or ordinary structural steel with anti-corrosion treatment.

Corner brackets

This simplest type of fastening is made by perpendicular welding of corners with a shelf thickness of at least 2 mm.
It can withstand moderate loads, but over time, vibration negatively affects the strength of the seam. In addition, accidental damage to the anti-corrosion coating can lead to a rapid decrease in the strength of the product and a change in its configuration.

Structures made of U-shaped profiles connected by bolts

Such brackets are more reliable due to the presence of additional stiffening ribs and a bolted connection that is resistant to vibration. Fasteners made of galvanized steel do not corrode for a long time and can be replaced with new ones if damage is suspected.

Brackets for outdoor unit

Brackets made of U-shaped profile with additional reinforcement

This design is similar to the previous one, but has slightly elongated vertical elements, to which an additional jib is attached at a certain angle. It gives the entire system absolute rigidity and allows it to be loaded with a fairly heavy load.

Brackets made of U-shaped profile, fastened with a horizontal strip

Such devices, in addition to all the positive qualities of the previously described models, also have resistance to horizontal displacement and ease of mounting to the wall. They can be installed under the most expensive and critical equipment.

For information! The presence of elongated holes on the horizontal shelves of the brackets makes them suitable for installation under any brand of air conditioners.

Connecting freon pipes

We move on to the stage of connecting communications.

Connect the flared tubes to the indoor unit of the air conditioner using adjustable wrenches.

If you have a torque wrench, it is better to use it.

Here are the recommended tightening torques for freon tubes of various diameters:

• 1/4 – 16-20Nm

• 3/8 – 35-45Nm

• 1/2 – 45-55Nm

Next, take the interconnect cable and twist it all into a single unit with the freon line using reinforced tape or vinyl tape.

Do not forget to stretch the insulation of the required diameter onto the copper tubes.

To prevent dirt from accidentally getting inside the tube, wrap its ends with electrical tape.

Error No. 8 Under no circumstances should the thermal insulation of the tubes be left unprotected.

Otherwise, from the street under the influence of UV rays, within several seasons it all turns into dust.

If your thermoflex is lightfast and not afraid of the sun, then think about the birds. Crows peck very well and take away such material for their nests.

Error No. 9 Also, do not leave any area indoors without insulation. Especially the junction points.

Condensation will gradually form here and eventually a neat trickle of water will appear on your wallpaper.

The line itself, wrapped with tape, is hidden inside the room in a plastic box.

However, if you have a short area and there are old wallpapers left, then instead of using a box, the highway can be covered with them. The result will be an almost invisible picture.

Next, pass the line through the through hole to the outside.

Drainage

Please note that the drainage hose must be located below the freon line.

Connect the air conditioner drain hoses.

For extensions, many use a regular metal-plastic pipe d-16mm. The factory drain tube is flared and metal-plastic is inserted into it, sealing the connection at the top with electrical tape.

However, over time, a fungus may form inside the metal-plastic material, which will not allow the water to drain away quickly enough.

Therefore, other installers use only corrugated pipes as drainage.

In addition, it is the corrugated drainage that allows you to connect directly to the bath without additional connections.

Connecting the air conditioner to the mains

To finish with the indoor unit, let's move on to connecting the power wires.

Having opened the front cover of the indoor unit, unscrew the plastic plug to connect the cable.

Having inserted the cable, connect it according to the electrical diagram. To do this, look for the following markings on the terminal block:

• L-phase

• N – zero

• grounding icon

Check on the power cable where you have phase and zero and connect the corresponding ends to your terminals.
When connecting a low-power air conditioner (up to 2.5 kW) directly from the switchboard without an outlet, you must have a three-core cable VVGng-Ls 3 * 2.5 mm2 in the groove.

A 16A circuit breaker is installed in the panel.

With a low-power condenser up to 1 kW, you can, of course, use a section of 1.5 mm2 + a 10A automatic, but 2.5 mm2 is a more universal option and will allow you to easily change the split system with a higher power in the future.

If the air conditioner will be connected through an existing socket, then use a wire with a 3*2.5mm2 PVA plug.

There is also nothing complicated about connecting the indoor and outdoor units. Here, as a rule, a 4*2.5mm2 or 5*2.5mm2 cable is used. The terminal markings on these blocks are the same.

Accordingly, throw a cable between them (not the PVS wire, but the VVGng cable!) and connect the wires of the same color to terminals L1 on the internal unit and L1 on the external one, N on the internal one and N on the external one, etc. Just follow the connection diagram and labels.

Sometimes the air conditioner itself in the room is powered not from the outlet, but from the outdoor unit (most often with inverter models). In this case, the exterior will have several more terminals.

This is phase-zero-ground. Then you lay the power cable from the outlet or diffavtomat in the switchboard outside, and not to the indoor unit.

Connecting the freon route pipes from the outside is similar to the room connection.

Air conditioner vacuumization

But for the next stage of work you will need a vacuum pump. It is necessary for vacuum drying of the freon line.

Mistake No. 10 You can never guarantee that all the moisture will simply be driven out by the freon itself. The air contains this moisture. Without normal vacuumization, sooner or later your compressor will fail.

If you do not bleed the air, the pressure in the system will be affected (it will rise). In this case, the compressor’s performance may drop by about 30-35%, and it will operate under constant load.

And the moisture contained in the air affects the rapid decomposition of oil and an increase in its acidity level.

This further leads to two consequences:

• destruction of the varnish insulation of the windings on the electric motor by the acidic environment and its failure

• gradual “washing out” of copper from the tubes and its entry onto the working surface of the compressor with a decrease in gaps

Therefore, if the invited “specialist” came without a vacuum pump, then know that very soon you will see him again. And you will meet him very often.

The operating time of the vacuum pump depends on the length of the line. The minimum length is 2m. If you get less, then sooner or later the oil from the compressor will definitely get into the evaporator and your air conditioner will not work for a long time.

For a standard short section, vacuumization time is from 15 to 20 minutes. It is counted after the direct creation of a vacuum (reaching a pressure of 5 torr). This can be checked on the pressure gauge manifold, or heard by the changed sound of the pump.

When the sound almost disappears, start counting the time from that moment.

Let's listen

To begin with, we simply plugged the Niagara 3000 into the network, after which it occurred to me to press my ear to the device. A distinct “electric” hum is heard - its presence is also noted by the manufacturer. However, from a distance of 30 cm this sound is already indistinguishable.

The heating that sometimes accompanies the operation of such devices was absent in our case. Related to this, by the way, is the documented possibility of installing the Niagara 3000 not only horizontally, but also vertically - if it’s more convenient, then why not?

To test the AudioQuest Niagara 3000, we used a less than standard audio package. The amplifier with a power of up to 100 W per channel was supplemented with a network player to test the digital setup. The analogue version was represented by a textbook vinyl player.

But for the acoustics - a pair of compact floor-standing speakers, exactly matching the power of the amplifier - they decided to add a couple more subwoofers to increase the load. I’ll leave the model names out of brackets, I’ll just note that all the equipment requires power, and this set was also carefully configured in advance.

If we analyze the level of components, then perhaps the Niagara 3000 has become a slightly redundant partner for such a set. Well, it’s all the more interesting what you can get with its use.

Two sockets for powerful devices.
At the top left is the Power Correction switch. On the other hand, our audio kit forced us to try the Niagara 3000 in more diverse modes. Judge for yourself: having three powerful consumers at once - two subwoofers and an integrated speaker - and only two powerful sockets for them, we had to invent options. And we decided to connect the components one by one.

So, first of all, the sound of subwoofers. On recordings with serious punch, the bass stood out, became more prominent, tangible and concrete. However, it cannot be said that its volume ratio has changed. Rather, it's about intelligibility, if such a term is appropriate in relation to a set of a pair of 10-inch woofers with a pair of passive radiators of the same caliber.

It was not possible to activate the overload indicator during the test

Our unemotional and precise amp added emotion to its understated precision, expanding and clarifying the stage and separating the top percussion. Particularly worth noting is the improved microdynamics, which was appreciated even with the full forte orchestra and chorus from Grieg’s “Peer Gynt” (“In the Cave of the Mountain King”).

However, I consider the main advantage that the AudioQuest Niagara 3000 was able to bring to the sound of our setup to be air. The pauses became clear and deep, and the solo instruments fell into place and came to life.

This was especially evident when working from the Niagara 3000 amplifier-turntable combo. We decided to use Smokey Robinson's classic, although not often heard, album, Yes, It's Your Lady, recorded in the early 80s.

I was not delighted with the initial “tuning” audition. Vocals, backing, instrumental parts - everything mixed into a single lump and did not want to separate. There were too many sounds and they interfered with each other.

Niagara 3000 helped put all this in its place. Playback literally jumped a class higher. The sound became “the one”, carrying the atmosphere of the heyday of disco-soul in the 80s. The soloist's sweet voice stood out and came to life. Everything became visible - and, unfortunately, the flaws of our vinyl...

On the other hand, the operation of a high-resolution DAC connected to the player system in the presence of an air conditioner and without it, in my opinion, did not have any pronounced differences. Of course, we could also try to connect both the amplifier and both subwoofers to the conditioned power supply, but, on sober reflection, we did not do this - the information received was already quite enough.

Checking pressure and sealing

Before pumping freon, be sure to check the drainage. To do this, having removed the filter, pour clean water onto the evaporator of the indoor unit, as if simulating the formation of condensation.

If the drainage is done correctly, the water will flow freely through the tube and will not overflow over the edge of the inner pan.

It is also advisable to check the pressure in the system before opening the freon line ports. The manufacturer, as a rule, fills 5 meters of refrigerant along the route, and reports this on the nameplate of the outdoor unit.

However, there are also half-empty copies (they save freon).

Next, the tightness of all connections is checked. Superprofessionals do this with nitrogen at a pressure of 38 bar at a reasonable price. But are you ready to pay money for such quality?

In the standard version, after disconnecting the vacuum pump, simply release a certain amount of refrigerant into the line (5-7 bar) and remember the pressure value.

Wait 20 minutes and check if the readings have changed. If the result is positive, using hexagons, the service taps of the air conditioner are fully opened and all the freon is released into the line.

Next, apply voltage to the air conditioner and test it in all modes. When cooling, measure the surface temperature of the evaporator with a pyrometer, or preferably a contact thermometer.

After reaching the operating mode, it should be at least +6C. If the temperature is higher, additional freon charging may be required.

In this case, a complete refill of the system is used more, rather than just refilling it, due to the complexity of the process.

If all installation stages are completed without any comments, you can enjoy the coolness and assume that your air conditioner is installed correctly.