Why plaster doesn't stick to the wall and how to fix it

Properties of plaster

First, let's figure it out: what properties should plaster have?

1. The solution can remain in a liquid (working) state for two hours.
2. The quality is checked by a two-meter rule, which is applied in all directions to mark unevenness. With average quality, up to five recesses are allowed, up to 3-5 mm deep. The higher the quality, the fewer errors there are.
3. The strength after 28 days should be above 20 MPa.
4. High adhesion.
5. High moisture resistance.

Specifications:

Beacons for plaster

What is a lighthouse? As you know, a lighthouse is a landmark for something. Such guidelines during plastering of the wall can be any hard marks that are set according to the level.

The beacons can be based on boards, nails, or dried mortar tubercles applied to the wall. But the best are perforated metal profiles, which in construction stores are called beacons. They can have different thicknesses. It all depends on what layer needs to be plastered. In addition, it should be taken into account that the thicker the beacon, the tougher it is.

Installation methods

First way. Dots are applied to the surface of the wall using a mortar of cement, tile adhesive or putty. A perforated metal beacon is glued to each point and then leveled using a building level. It should be noted that a short level is inconvenient for proper plastering (deflections occur in places of pressure). But don’t despair if you only have a short level available. First, a rule is applied to the beacons (without it it is impossible to plaster, so it must be at hand). Then the building level is applied to the rule.

Second way. Using a hammer drill, holes with a diameter of 10 mm or more are drilled strictly along a vertical line. The holes are filled with wooden choppers; it is better to make them cone-shaped so that the lighthouse profile can be attached to them more easily. Using a cord or fishing line, each row of choppers is leveled. You can trim the row along the marking thread using a hammer or a hacksaw. The beacons are attached to the already leveled chopiks using screws 2.5 cm long. The gaps between the chopiks are filled with a solution based on cement and sand. This is done to ensure that the rule does not bend under pressure. This method of placing beacons is used for very uneven walls with large differences. The first method is not suitable, since the layer of plaster will not stick.

The length of the rule used for work must be at least 10 cm greater than the distance between the beacon profiles.

When choosing the first method of installing beacons, you must first let them dry and only then start plastering.

not plastered

Useful

See what “not plastered” is in other dictionaries:

plastered - smeared Dictionary of Russian synonyms. plastered adj., number of synonyms: 1 • smeared (7) ASIS Dictionary of Synonyms. V.N. Trishin ... Dictionary of synonyms

PLASTERED - PLASTERED, plastered, plastered: plastered, plastered, plastered. prib. suffering past vr. from plastering. Ushakov's explanatory dictionary. D.N. Ushakov. 1935 1940 ... Ushakov's Explanatory Dictionary

Plastered - adj. from the parables according to ch. plaster I Explanatory Dictionary by Efremova. T. F. Efremova. 2000 ... Modern explanatory dictionary of the Russian language by Efremova

plastered - urn plastered; briefly form en, ena, prich ... Russian spelling dictionary

plastered - adverb; cr.f. stuktu/ren, stuktu/rena, reno, rena. The walls of the house, plastered by an old master, were very smooth... Russian Spelling Dictionary

plastered - plasterer/enn/y... Morphemic-spelling dictionary

plastered - plastered, en, en, en, en... Russian word stress

not plastered - not plastered ... Spelling dictionary-reference book

not plastered - not plastered, urinary, and ... Russian spelling dictionary

plaster - plaster, plastering, plastering, plastering, plastering, plastering, plastering, plastering, plastering, plastering, plastering, plastering, plastering, plastering, plastering, plastering,... ... Forms words

Source

Proportions for plastering walls: binder

Today you can see many different options for plaster mortar on the market. To choose the optimal composition, you need to know everything about the types of plaster mixtures.

All builders who try to keep up with the times, develop and improve the level of their work know that the mixture must consist of an aggregate and a binder component. When it comes to plastering, the classic filler in the proportion of cement for plastering walls is sand. This is an essential component that prevents cracks from occurring and makes the material durable.

Clay, lime, cement or gypsum powder is mixed into the composition as a binding component of the plaster solution.

Cement mixtures are most often used for external finishing work, since the external part is exposed to atmospheric influences and various weather phenomena. Indoors, cement is used to plaster the bathroom or kitchen - places with high humidity levels.

Lime mixtures are designed for rooms with the most stable humidity. This is a universal tool that can cope with many tasks.

Clay mixtures can be used exclusively in dry climates and for finishing walls inside a building. The main thing is maintaining the optimal humidity level.

Gypsum material is used when plastering surfaces in those rooms where a stable microclimate is maintained 365 days a year.

You can order from us:

The purposes of using any plaster mixture are to level the surface, seal seams and cracks, improve the heat and sound insulation characteristics of walls and ceilings. In modern construction, the most popular are cement-sand, cement-lime and gypsum compositions. Each of these plastering materials has advantages and disadvantages and specific applications.

Alabaster compositions are usually used for interior work in rooms with moderate and low humidity. They are suitable for almost all types of surfaces, including ceramic, wood and polymer, on which cement plaster does not adhere.

Cement-sand compositions are able to maintain performance characteristics under high mechanical loads and in wet conditions. They are used for finishing facades, basements and basements, and rooms with high humidity. They are also suitable for dry rooms.

Adding lime to plaster compositions increases their plasticity and ease of use, and gives the coating bactericidal properties. The plaster layer, which contains lime, is not attacked by fungus and mold.

How to prepare plaster mortar

Plaster solutions are divided into:

• simple (lime, cement, clay);
• complex (lime-gypsum, cement-lime, lime-clay, etc.).

In order for the solution to be optimal for work, the proportions of fillers and binders must be observed when preparing it. In this case, a normal solution will be obtained.

If there is an excess of binder material, the plaster mortar will become greasy. This type of plaster will crack and shrink as it dries and hardens. If there is an excess of fillers, the solution will become thin, that is, not strong enough. The fat content of the solution is determined by stirring it.

If the mixture does not stick to the shovel, then such a solution is considered lean. A normal solution sticks slightly, but a greasy solution sticks a lot.

To prepare the lime mixture, add some quartz sand and water to the dough, then mix the dough thoroughly. Sand is added in portions until the mixture reaches normal fat content.

Lime is not only a binding material, but also a plasticizer. This property helps it quickly and reliably grip both stone or brick surfaces and wood. However, such a solution hardens for quite a long time.

Due to its poor moisture resistance, lime is extremely rarely used for plastering external walls. In addition, such plaster is fragile and is easily destroyed by mechanical stress. But thanks to these properties, lime plaster can be easily and quickly removed by hand if repairs are necessary.

Gypsum is added to lime mortar to speed up hardening. For this purpose, gypsum is poured into a container with water and mixed thoroughly. Add the dough to the resulting solution and mix again until smooth.

It is extremely important when adding gypsum that all manipulations are carried out very quickly and in small portions. The solution containing gypsum will begin to set within 5 minutes after preparation. After half an hour, the mixture will turn into a solid mass. Therefore, it is pointless to prepare a lime-gypsum mixture for future use. When lime cement is added, the mixture acquires additional strength and moisture resistance.

How much will it cost to use a pneumatic bucket?

A pneumatic bucket made independently allows you to save money: the costs will only be on components and materials. The purchased tool costs differently, depending on the manufacturer:

• “Plaster’s Dream 1” : the cost of a ladle is from 6,000 rubles, the price of a compressor with a receiver is from 5,000 rubles.
• “Plaster’s Dream 2” : a pneumatic bucket costs from 11,000 rubles, a compressor of the required performance – from 15,000.
• “PK-1.1” : the price of the bucket is from 5,000 rubles, the cost of the compressor is similar to the previous point.
• Pistols Matrix, WESTER KP-10, “Hopper” RK-1 : can be purchased from 2000 rubles.

The consumption of plaster depends on its type. To order the required quantity, be guided by the norms:

• gypsum mixture applied in a layer of 10 mm will disperse in an amount of 9 kg/sq. m;
• cement plaster is heavier, its consumption will be 16-17 kg/m2.

To the estimated costs you need to add the cost of a hired plasterer (if you are not going to do this work yourself). Masters, depending on experience, the market situation in your region and their own “appetites,” charge from 200 to 800 rubles. per square meter. It’s possible to find a plasterer who charges 400-500 per sq. m. m. But if you have at least minimal construction skills, you can handle plastering yourself.

not plastered

Useful

See what “not plastered” is in other dictionaries:

plastered - smeared Dictionary of Russian synonyms. plastered adj., number of synonyms: 1 • smeared (7) ASIS Dictionary of Synonyms. V.N. Trishin ... Dictionary of synonyms

PLASTERED - PLASTERED, plastered, plastered: plastered, plastered, plastered. prib. suffering past vr. from plastering. Ushakov's explanatory dictionary. D.N. Ushakov. 1935 1940 ... Ushakov's Explanatory Dictionary

Plastered - adj. from the parables according to ch. plaster I Explanatory Dictionary by Efremova. T. F. Efremova. 2000 ... Modern explanatory dictionary of the Russian language by Efremova

plastered - urn plastered; briefly form en, ena, prich ... Russian spelling dictionary

plastered - adverb; cr.f. stuktu/ren, stuktu/rena, reno, rena. The walls of the house, plastered by an old master, were very smooth... Russian Spelling Dictionary

plastered - plasterer/enn/y... Morphemic-spelling dictionary

Plastering clay walls with your own hands

Published by: Arthur Kanapatsky 0

You can find clay walls not only in old houses. The desire to become an eco-friendly homeowner has revived the trend of using age-old technologies. The use of new construction techniques makes it possible to build strong and durable buildings with clay walls. Their advantage is keeping them cool in hot weather and retaining heat for a long time at low temperatures. We will study in detail how to qualitatively finish clay surfaces with plaster with our own hands.

Selection and preparation of materials for work

The characteristics of clay walls include not only positive properties; such surfaces have a number of finishing features. When choosing a material for plaster, you should take into account that a composition that is lighter in weight is suitable for a clay surface. Therefore, work on plastering external walls is carried out with solutions containing lime; interior decoration is recommended to be done with a gypsum or clay mixture. It is strictly not recommended to plaster clay surfaces with cement mortar. This will lead to the destruction of the finishing layer due to its severity.

The finishing technology involves applying three layers: rough, finishing and decorative. For the initial stage of plastering walls you will need:

• Clay. According to plasticity parameters, it is divided into light, whose indicators vary between 0.17-0.27, and heavy, for which the plasticity number lies beyond 0.27. Its color also matters. The most common is red, although material in white, grey, yellow and black is found.

Comment! Despite the natural origin of clay, sometimes it contains minerals (quartz, magnetite, etc.) that have an increased level of radioactivity.

• Wood sawdust. For rough plastering of clay walls, only thoroughly dried sawdust is used. It is important to be sure that they do not have fungal diseases. Fresh material cannot be used for finishing clay walls; at least a year must pass from the moment they are received.
• Sand. Material of the middle fraction will help ensure high-quality plastering of walls; it is better to sift out large inclusions.

To prepare a solution for rough plaster, first sawdust is mixed with sand, then clay and water are gradually added.

For the second layer of plaster you will need cement, clay and sand. Due to the different properties of clay, the optimal proportions for the solution will have to be selected independently, depending on its fat content and plasticity. The approximate ratio of components is 1:1:3. The readiness of plaster for finishing clay walls with your own hands is determined in various ways:

• You can roll a small ball that does not stick to the skin and crush it on a flat surface. With an ideal ratio of components, cracks should not appear on the sides.
• The second option is to form a flagellum 20 cm long with a diameter of 2 cm, and roll it into a ring. The correct plasticity of the mortar for plastering walls is again determined by the absence of cracks.

Cement-lime mixtures

Cement mortar in its pure form is not used so often because it has poor adhesion and increased cracking. In addition, not everyone has the opportunity to use expensive dry mixes, so lime plaster is a good alternative. This is a very economical version of the mixture, which is convenient to work with due to its plasticity.

This option is also good for use in private homes due to its bactericidal properties - this is additional protection against fungus. Lime mortar is chosen mainly for rough finishing of walls in rooms with normal and low humidity. Unlike cement mortar, a lime-based mixture is well suited for plastering over shingles because it adheres well to the wood surface.

The disadvantages of this mixture include low grade strength, in contrast to mortar based on Portland cement. But this drawback does not play a special role; for plaster, compressive strength is not so important as a good level of adhesion and ductility.

Composition of lime mortar for plaster:

• 1 part cement;
• ½ part slaked lime;
• 5 parts sand;
• 300 ml liquid soap.

The mixture turns out to be very elastic and adheres well to the wall; after drying, no cracks appear on the surface. Liquid soap adds a pleasant scent and increases elasticity.

Cement-lime mortar for plaster can be prepared in another way:

• 1 part lime sour cream;
• 2.5 parts sand;
• 0.12-0.25 parts of cement (depending on the amount of lime).

It is best to take quicklime and slak it yourself. 50 kg will require 13 buckets of water. Please note that when slaking, the lime will increase 2.5-3 times, so this work is done in a barrel of the appropriate volume.

Formation of the rough layer

Sawdust provides reliability to the plaster mortar. If they are not available, in order to apply the rough composition to the gypsum surface, you will need to attach a reinforcing nylon mesh. It is better to fix it directly with a solution; when used to secure nails, the integrity of the wall is compromised and the strength deteriorates. It is practical to treat clay walls with plaster with an assistant who will point out places that need improvement. The process includes the following steps:

• To work, you will need a grater board or spatula.
• Two or three mounds of plaster are applied to the working tool.
• The tool with the solution is pressed tightly and distributed over the surface.
• The direction of movement is from bottom to top. You should try to distribute the plaster as evenly as possible.
• The flat surface of the wall is checked using a building level. Identified irregularities are eliminated immediately after detection.

If the wall is relatively flat, a starting layer of 1 cm is sufficient. If there are significant unevenness on the clay surface, the plaster layer can increase to 3-5 cm.

Advice! When processing large areas of clay walls with your own hands, it is much more convenient to apply plaster using beacons. This will speed up the entire work process and increase the quality of the finish.

After applying the rough layer of plaster solution, time is required for it to dry completely. The entire process takes on average 4-6 weeks. The approximate drying period for a 1 cm thick layer at room temperature is 5 days, and it is not recommended to speed up the process using a technical hair dryer or heaters. Therefore, it is better to plan the work for the warm period. It is optimal when the initial finishing begins in late spring - early summer, although it all depends on the region where the house with clay walls is located. Professional steps for applying plaster to walls can be seen in the following video:

Selecting ready-made formulations

Choosing the type of plaster - gypsum or cement - is just the beginning. Next, you will have to choose the manufacturer and the composition itself - there may be several products with slight differences.

There are many different brands of plaster in construction stores.

Good gypsum plasters

The most popular gypsum plaster is Rotband from Knauf. This is a really high quality product that is easy to use even for beginners. The same company has other products - Goldband and HP Start. They are cheaper, and the quality is quite decent.

The most popular type of plaster is Rotband.

NR Start is a gypsum-lime composition, Goldband is a gypsum composition. The difference between Rotband and Goldyuand is the thickness of the minimum layer. Rotband’s is 5 mm, the second’s is 8 mm. Otherwise, the technical characteristics are very similar - both consumption (8.5 kg/m 3 with a layer thickness of 1 cm), and maximum layer (50 mm), and compressive and bending strength. The density in the hardened state differs slightly:

980 kg/m 3 for Goldband and 950 kg/m 3 for Rotbabd. Scope of application: any residential and non-residential heated premises, including kitchens with bathrooms.

Volma Layer, Osnovit Gipswell, Eunice Teplon, and Prospectors also speak well of gypsum plaster. They cost less, give good results, but it’s still easier to work with Rothband and the “company”. Based on the results of working with these brands, there are both positive and negative reviews, but in general, the quality is not bad.

Ready-made cement plasters

Cement plasters are available for manual and machine application. We will talk about compositions for manual application. For interior work, Forward, Weber Vetonit, Osnovit Startwell, Weber Stuk Cement are good. They fit well on a clean, pre-moistened surface. For better adhesion, it is better to pre-prime the walls and, after drying, begin the plastering process itself.

Cement plaster is also noticeably different

If you choose cement-based plaster for exterior work (including for plastering an open loggia or balcony), you need façade compounds. They differ from ordinary ones in the increased number of freezing/unfreezing cycles. Facade cement plasters - Yunis Silin facade, Osnovit Profi Startwell, Knauf Unterputz, Bergauf Bau Putz Zement. Ceresit CT 24 Light plaster is suitable for both facade and interior work.

Aerated concrete walls require special plaster. It has increased vapor permeability to prevent moisture from being trapped inside the wall. This is Ceresit CT 24, Knauf Grundband (contains the smallest particles of polystyrene foam, which increases its thermal insulation properties and reduces consumption).

Finishing

The final leveling of clay walls occurs at the stage of finishing with plaster. After bringing the surface to a smooth state, you will need to grout. It requires a solution of sand, clay and cement. It is better to avoid sawdust due to its swelling and disruption of the smoothness of the wall. The approximate ratio of these components is 3:1:1, it all depends on the quality of the clay, sometimes the amount of sand needs to be increased to 4 units. The finishing plaster solution should be liquid; this composition is easier to apply to clay walls. The absence of a coarse fraction in the sand composition will provide a smoother surface during finishing. It is recommended to use only dry material. The procedure for preparing the plaster solution is as follows:

• the clay is soaked a day before preparing the composition;
• after softening, excess liquid is removed, and the clay is kneaded so that there are no large lumps;
• dry sand is combined with cement;
• All components are thoroughly mixed with the gradual addition of clean water.

The drying period for finishing plaster applied to clay walls ranges from 1 to 3 weeks, it all depends on the surrounding microclimate. The naturalness of the process is a prerequisite; any artificial acceleration will provoke cracking of the clay walls.

Final decoration

At the final stage, after the finishing layer has dried, the walls are treated with lime. Traditionally, the procedure involves applying several layers. Alternatively, the surface of clay walls can be treated with fine-grained sandpaper. After sanding with sandpaper, it is necessary to apply a primer. It is better to do this twice at intervals for complete drying. Next, the clay walls are covered with a gypsum mixture. The prepared surface can be painted or covered with wallpaper.