Do-it-yourself tennis table: TOP-150 photos of the best manufacturing ideas. Master class on creating a tennis table at home

Nowadays, a healthy lifestyle is very common.
And table tennis can be a great way to keep fit while also having fun. At the same time, it is not necessary to sign up for a gym, just get your own tennis table. And in order not to buy expensive equipment, you can always assemble the table yourself.

A little history

The name "Ping Pong" appeared at the end of the 19th century. A number of historians believe that the game owes its appearance to the rainy weather of Foggy Albion, which forced tennis matches to be interrupted.

To be absolutely precise, table tennis and ping-pong are two different sports, but in everyday speech they are very often used as synonyms.

The whole difference between Olympic and amateur sports lies in the “clothing” for the rackets. Table tennis uses rubber-coated rackets, while ping-pong uses either uncoated or cork-and-parchment-coated rackets.

The first set for the game was released by Jaques of London in 1891. Well, many modern home craftsmen know how to make a tennis table without resorting to the services of branded salons and stores and willingly share their knowledge on their own websites.

Table tennis table drawing and dimensions

Important : the dimensions of the standard playing field are 1525 mm by 2740 mm.

The height of the playing surface above the floor should be 760 mm . The thickness of the tabletop for an amateur tennis table varies in the range of 12-28 mm, but the average is 18 mm.

It is necessary to pay attention to the fact that the supports of the tennis table should not extend beyond the contour of the playing field. Ideally, the support structure is recessed into the playing field and lags behind the edge of the tabletop by approximately 200-300 mm.

For indoor play

According to the table manufacturing diagram, you will need:

• legs (8 pcs.);
• crossbars (4 pcs.);
• lateral ligaments and spacers (2 pcs.);
• clamps (8 pcs.);
• countertops (2 pcs.);
• hinge plate, brackets, axle (8 pcs. each) and lugs (16 pcs.).

On the World Wide Web it is not difficult to find photographs of a tennis table with a step-by-step explanation of how to assemble such a product.

Second option

Knowing the standard dimensions of a tennis table (2.74 by 1.52 and height 76 cm), you can make sports equipment in the simplest way.

Sheets of plywood and legs are purchased. Everything is held together with self-tapping screws, the product is painted, and in just a couple of hours the table is ready!

Note!

• DIY induction heater ♨️ - reviews of the best manufacturing options. Varieties of homemade device designs + step-by-step master class (160 photos)

• Do-it-yourself Gauss cannon: TOP-130 photos of the best ways to create it yourself. Design features + master class for beginners

• DIY clamps - a step-by-step master class for beginners. Schemes for manufacturing different designs + 170 photos

What you need to prepare

1

2

3

4

First of all, you need to think about the platform on which the table will be installed. If the table is to be placed indoors, then a standard-sized table requires an area of ​​six by twelve meters. Mini tables can easily fit inside a more or less spacious room. But if the table is on the street, then get ready to level the area for it.

It is better to make the table matte, otherwise glare may interfere with the game

Ideally, you need to build a flat area with concrete pouring, or use a special covering (playing on the ground or sand is not always convenient, especially after rain).

After this, we need to determine the size of the table - standard, midi or mini (or we need to assemble a table for children). Also decide whether we are assembling a table with a folding mechanism or not. If the table is completely stationary, then you can do without using wheels, although it is still better to make the structure more mobile.

Materials required for a tennis table (different options are possible):

• plywood (for the countertop it is better to use moisture-resistant plywood, at least twelve to fifteen mm thick);
• chipboard or chipboard (but remember that chipboard is less moisture resistant);
• board one hundred by twenty-five mm (you can make a base or stiffeners from it);
• fifty-fifty timber for making legs (you can purchase beams of the required length so as not to cut them yourself);
• metal corners, fastenings for legs, self-tapping screws;
• matte paint of dark blue (or dark green) (it is better to choose matte paint, because it does not glare in the sun).

What tools are best to use? The most suitable option is a jigsaw and a screwdriver. For painting you will also need a fine-nap nylon roller.

Outdoor table

Making a folding table is more difficult, but such equipment is much more practical. The difficulty lies in the large number of connections and parts that must be carefully adjusted to each other.

You shouldn’t get hung up on exact measurements – a couple of millimeters or even centimeters are not decisive. The most important condition for a normal product suitable for playing is a flat and smooth table surface.

Particular attention should be paid to the material - if the product will be constantly outdoors, materials such as fiberboard or chipboard cannot be used. Even covered with several layers of paint, playgrounds made from these materials will very quickly lose their shape and bend.

Minuses

Inconveniences are caused by the lack of transport rollers on the table, a thin tabletop and materials that cannot ensure a uniform rebound.

This drawback is found in outdoor products: melamine countertops are inferior in performance to chipboard, and metal edging disrupts the uniformity of rebound.

Operational problems arise in the following cases:

• there is no anti-reflective coating on the surface;
• the rollers are made of insufficiently strong material and cannot withstand weight;
• The tabletop material is fragile;
• the surface is uneven, damaged or deformed.

Necessary materials

In order for the table to “tolerate” any weather conditions (heat, direct sunlight, cold, rain, snow), it must be made of either plastic or laminated, water-repellent birch plywood.

This is the material that is best used when making a do-it-yourself tennis table for the outdoors. The thickness of the material used should be in the range of 16-20 mm.

The traditional color for gaming tables is green. If you purchased plywood of a different shade, you should paint the playground in the desired color, this will only enhance the “capabilities” of the playing surface to withstand precipitation.

Note!

• Do-it-yourself electric scooter - a master class with step-by-step instructions for doing it yourself. Tips and simple patterns for beginners + the best photo reviews

• DIY rocking chair: TOP-120 photos of the best manufacturing options. Master class on creating a rocking chair at home

• Smokehouse from a gas cylinder - the best master class on making a homemade smokehouse with step-by-step photo diagrams for beginners

Since transporting a standard sheet of laminated plywood is extremely difficult, you can purchase a couple of sheets of a smaller size, and on the spot, during work, fasten them together using a beam of a suitable size.

Important! Complete moisture resistance will be provided by edging the edges of the table top with an aluminum profile.

What can you make a billiard table from?

A billiard table is a very complex product, it is a luxury item. The player can lean on the tabletop or put his entire weight on it, so the table must be heavy and durable. It should not vibrate or warp. The ideal dimensions would be: height - 80 cm, length - 2 m, width - 1 m.

The product consists of a frame, tabletop, base of the playing surface, supports, sides and pockets.

The billiard table has its own requirements:

• strength and reliability;
• mobility;
• be able to transform into a tennis or dining table.

The product is made from quality material. Previously, solid wood was used: oak or beech. For a cheaper option, they used pine. From the legs to the tabletop, one type of dense wood was taken.

The best materials for making countertops and sides are mahogany, ash, oak, and pine. The tabletop can be made from a solid stone slab, concrete, metal, plastic and chipboard (chipboard with a facing film based on paper and melamine resin) with a thickness of at least 20 mm, or more.

Chipboard table top

There should be no cracks on the chipboard sheet. The main condition for the product is a flat surface. It quickly wears out and becomes deformed due to the bounce of the balls. The thicker the sheet, the better.

Plywood table top

Plywood can be a cheaper option than stone or timber. It is better to use birch plywood with a thickness of at least 24 mm, which can be coated with water-based acrylic paint in 2-3 layers. This will improve the moisture resistance of the plywood.

Laminated plywood

The material is laminated with non-flammable melamine. Laminated plywood does not warp or bend during use. From this material you can make a tabletop solid or split. Can be used outdoors and tolerates temperature changes well.

The base plate of the product consists of three or five parts (depending on the size of the field), which are connected using threaded ties. The seam between the slabs is carefully puttied, the surface is leveled so that the joints between the slabs are invisible.

If you run your palm over the countertop, the joints should not be felt.

Base material

The base can be made of different materials. The main thing is that it is resistant to damage.

The base material for the product can be:

1. The natural stone is Ardesia slate. It is durable due to its slate structure. A falling ball weighing 290 grams will not leave dents or cracks on the slab. It has an ideal surface for rolling out balls; damage that may occur during operation can be easily eliminated.
2. Made from synthetic granite - synthetic granite. A composite material based on marble chips bound with epoxy resins. Has the property of crumbling.
3. It is more difficult to obtain a slab of the required size and thickness from marble. Marble is susceptible to damage and difficult to polish.
4. Made from laminated chipboard (laminated chipboard). The big advantage of a slab made of this material is its low weight, the minus is increased background noise. Chipboard wears out quickly.

A good foundation must withstand a considerable load of weight without changing its geometric parameters.

Legs

The table must be strong and stable, because... During game battles, opponents may accidentally lean on or push him. It is better to make the supporting base of the platform from a metal frame. For this you will need:

• four pipes measuring one and a half meters;
• squares - four one meter long and the same number two meters long;
• eight half-meter squares.

Frame assembly

Let's look at the instructions on how to make a frame for a tennis table at home.

Step No. 1. Using two-meter squares, we connect a couple of pipe sections and weld them together. The first crossbar is located twenty centimeters from the top edge, the second seventy centimeters lower.

Note!

• Do-it-yourself compressor: TOP-130 photo reviews of finished compressors. Step-by-step instructions + diagrams and drawings

• Do-it-yourself wind generator: TOP-170 photo reviews of finished devices. Detailed DIY instructions for beginners

• Do-it-yourself spot welding - the best master class on making homemade spot welding with step-by-step photo diagrams of do-it-yourself work

Step No. 2. Align the assembled frame and weld it.

Step No. 3. A similar operation is carried out to design the second pair of table legs.

Step No. 4. In the place where the table is installed, holes more than half a meter deep are dug, sand is poured in and the legs of the tennis table are dug in.

Step No. 5. The table legs are fixed in the ground with cross-shaped mortgages. Using a spirit level, it is necessary to achieve the most uniform height of the table legs.

Step No. 6. The holes are filled with bitumen or cement.

Drawing game lines

In order for the table to be ready for play, markings must be applied to it. A white line 3-5 mm wide is drawn in the middle of the table. Before applying paint, you should use masking tape to mark the boundaries of the center line, this way you can clearly draw the boundary without getting dirty.

Stepping back from the edges along the entire perimeter of the site by 15-20 mm and also marking the boundaries with tape, we apply white paint to indicate the playing area of ​​the table.

Assembly

The last stage of work on making the table will be attaching the playground to the metal base. This can be done in two ways.

First option. Three or four holes are drilled in each table leg plate and the tabletop is secured with screws.

Second way. Through holes are drilled in the table legs, as close to the surface as possible. The playground can be fixed motionlessly either with pieces of reinforcement or with massive wooden splinters inserted into the holes. This option allows you to remove the platform and store it in a dry room during the winter.

Using scraps

When making a folding tennis table with your own hands, a certain amount of scraps remains. From these, as a bonus, you can make several rackets for the game. Markings are applied to a piece of plywood:

• draw a rectangle with dimensions 2x16 centimeters;
• semicircles with radii of eight centimeters are drawn on the wide sides;
• from the center of the picture we draw a rectangle with dimensions of 3.5x18 centimeters;
• cut out the racket with a jigsaw;
• use glue to thicken the handle;
• We clean the glued parts with clamps.

All that remains is to glue the shock-absorbing material to the shock part of the product and you can start playing in the fresh air.

General characteristics

If we consider the classic version of the ping pong table, it has the following dimensions:

• length 2.74 m;
• width 1.525 m;
• height 0.76 m;
• mesh height 15.25 cm;
• the mesh protrusion on the sides is 15.25 cm.

One of the most basic indicators of the quality of a table is the rebound of the ball from the playing surface (English: Rebound Factor). The ideal rebound is measured in this way: from a height of 30 cm, the ball is released without effort, and for the first time it should bounce to a height within 25-30 cm. This indicator should be the same over the entire area of ​​the tabletop.

Parameters of a classic tennis table.

Why is this factor so important? The quality of the ping-pong game will depend on the rebound of the ball. With a small rebound, the game will become too slow, sluggish, and will lose all excitement and passion. The ball's bounce rate is directly related to the characteristics of the tabletop - the material and its thickness.

Thickness and color

The thickness can vary between 12-28 mm for tables with different purposes (outdoor or indoor), but in any case, the playing surface must provide a standard ball bounce.

Gaming tables also necessarily have markings - there is a white border 2 cm wide along the edge, and a dividing longitudinal strip 3 mm wide is strictly in the center.

The surface color can be blue and green, and amateur models also use brown and gray. Interestingly, the shade of the playing surface can influence the nature of the game:

• blue color promotes excitement;
• and green - for proven tactical decisions.

The surface can also be glossy or matte. It is recommended to use a matte surface - there is no glare on it, so it is much easier to track the ball and play effectively.

All tennis tables can be divided into the following groups:

1. Professional. The thickness of the table top for such models is 22-28 mm, the weight can reach 140 kg. The table is highly stable and provides the best playing conditions.
2. Amateur. The tabletop is somewhat thinner - 16-19 mm; MDF or chipboard is often used to make the playing surface, intended for indoor use.
3. All-weather. As the name suggests, the product can be placed both outdoors and indoors. To ensure resistance to water, temperature changes and UV rays, the surface is made of plastic and coated with special protective compounds. All-weather models are lighter in weight (up to 70 kg) and can be collapsible or stationary. The thickness of the tabletop is within 12-20 mm.

Folding tennis table.

The folding design has several significant advantages - firstly, saving space for storage, and secondly, the ability to play alone by fixing the other half of the tabletop vertically.

You can make a tennis table with excellent characteristics with your own hands if you use competent instructions, drawings with measurements and photos. We offer you several design options for different conditions.

Also read: DIY country table.

Folding option

The dimensions of plywood sheets sold on the market are perfect for making a folding table. In general, this material has the disadvantage that it sags over time, so it is better to make the tabletop from two sheets.

The joint and possible minimal gap at the location of the mesh are quite acceptable. When choosing a material, special attention must be paid to its quality. The surface must provide the necessary quality of rebound of the ping pong ball.

Important! Choose first or second grade material. One side of the plywood must be sanded. Use the cutting service when purchasing material so as not to have to do this work on site.

Looking at the pictures of the tennis table, you will notice that the tabletop is made of a maximum of two sheets. A larger number of pieces sharply reduces the quality of the playground and it is not recommended to make it from more than a couple of pieces of material.

Product Operation

A tennis table can be outdoor, homemade or home, all-season, etc. These models are used either indoors or installed outdoors. Equipment installed indoors may become deformed due to natural phenomena. When it wears out, the quality of the game deteriorates and danger arises. Assembly and disassembly are very important in operation. By assembling the product according to the instructions, observing the standard, you will save time, parts will not be damaged, and players will not be harmed. The product must be transported very carefully and carefully.

Tennis tables are intended to be played on only. Sometimes, according to the instructions, it can be transformed into a table for the home or at the dacha for a picnic as a dining table

The tennis table can be played by one, two or four players. You cannot sit or lie on these tables. The legs on casters are equipped with a brake system. Otherwise, the model must be installed on a flat surface so that it does not slip or move. To avoid injury and damage, it is necessary to periodically check the clips, fasteners and screws on the equipment. Tighten and secure parts as needed. The countertop also needs to be looked after. Make sure there are no scratches or abrasions. It must be wiped without using detergents. Use special care products. When storing, use special cases.

Recommendations for choosing equipment:

• The material for the frame and tabletop must be durable and resistant to weather changes;
• Moisture-resistant models are universal options that tolerate moisture, but not temperature changes;
• Anti-vandal ones are suitable for long-term installation.

Athletes train on professional or advanced floor equipment for convenience. Amateur models are budget-friendly, they are light in weight, and they are compact when assembled.

Details

Work begins with preparing the largest part - the gaming table. If the pieces of material are not cut at the place of purchase, then they should be brought to standard sizes.

In order to increase the service life of the tabletop, its ends should be treated. The edge is cleaned with sandpaper. Even more reliable protection is edging the edges with squares.

The supporting frame is made of half-meter bars and longitudinal beams. Height-adjustable furniture legs can be used as supports.

Top 4 tables for home use

GIANT DRAGON Power 800

A good amateur model, which is intended for use in enclosed spaces. The table can be used both at home and at school, clubs, etc. places. For greater comfort, the tabletop is made of MDF, which is equipped with a high-quality anti-reflective coating. The thickness of the tabletop reaches 18 mm, which provides users with comfortable gaming.

Also, an additional advantage is the presence of a metal edge, which will provide the tennis table with the necessary rigidity. For safe transportation and movement there is a convenient Twin Multi-Security folding system. The mesh is attached to the table; dismantling/installation is not required, which will significantly increase the durability of the device. The dimensions of the structure fully comply with international standards, which makes it possible to hold small school competitions.

The average cost is 21,000 rubles.

GIANT DRAGON Power 800

Advantages:

• Low price;
• Reliability;
• Build quality;
• Acceptable thickness;
• Rigidity;
• Folding safety.

Flaws:

• Not detected.

DONIC INDOOR ROLLER FUN GREEN

A high-quality German table at an affordable price, which is intended for private use. Thanks to the convenient folding and unfolding system, a person can safely move the device. When folded, the design does not take up much space, which allows it to be stored with maximum convenience.

To ensure maximum stability, the manufacturer has equipped the device with good rigidity. There are 4 wheels that ensure high-speed movement of the structure from one place to another so that the table does not move during the game, there are special stoppers. The mesh is installed immediately and does not require dismantling.

The average cost is 22,000 rubles.

DONIC INDOOR ROLLER FUN GREEN

Advantages:

• Convenient racket and sword holder:
• Reliable design;
• High-quality assembly;
• Doesn't take up much space;
• Equipment.

Flaws:

• Not found.

Scholle T500

A good design that will suit most ping pong players. All sizes are made in accordance with international requirements, which will ensure comfortable playing. The main material is 12 mm MDF, which is equipped with an anti-reflective coating. The table has good moisture resistance and is also durable.

The big advantage is the safety of the material, which is important for indoor use. The design is completely foldable, making it easy to transport and store equipment. There is a possibility of a single game mode. The set includes 2 rackets, 4 swords and a net.

The average cost is 17,500 rubles.

Scholle T500

Advantages:

• Reliability;
• Quality manufacturer;
• Low cost;
• Equipment;
• Possibility of solo play;
• Good gaming characteristics.

Flaws:

• Not detected.

START LINE TRAINING

A high-quality model, made in accordance with all international standards, will provide the player with a high-quality game. Made from popular material: chipboard with a thickness of 22 mm, which provides excellent rebound. There is also a metal edging.

Thanks to the comfortable legs, a person is able to independently adjust their height, which makes it possible to play on uneven surfaces. The weight is 96 kg, so moving the table will not be an easy task.

The average price is 20,000 rubles.

START LINE TRAINING

Advantages:

• Reliability;
• High-quality assembly;
• Price;
• Good bounce;
• Folding.

Flaws:

• High mass.

Final design

The assembly process is not difficult. It is advisable to make reinforcements in the places where the legs are attached. Load distribution is achieved by installing metal plates at the points of fastening with bolts or screws.

All that remains is to carefully secure both sides of the tabletop to the frame and make the necessary markings.

Country competitions

Active recreation in an ecologically clean place is a great option to strengthen your health and boost your immunity before the long cold months of the year. Building a tennis table for a summer cottage is not difficult.

The main condition is the availability of free space of 5x7 meters. Having the necessary materials - sheets of plywood, a couple of three-meter boards, self-tapping screws, you can safely get to work.

Build process

The simplest construction trestles of the required height are made from available materials. Then:

• trestles are installed at the same level;
• the boards are laid and screwed with screws to the length of the tennis table;
• sheets of plywood are laid over and secured with slats;
• The table top is sanded and several layers of antiseptic are applied to it.

If, when leaving your summer cottage, you do not have time to disassemble the table and insulate it from the effects of precipitation, it is recommended to sew a cover from waterproof fabric. This way you can protect the product from damage, and during your next visit to the dacha you can again organize a family ping-pong tournament.

Guarantee

The manufacturing company provides a guarantee for the product only if the buyer followed the rules of operation and storage. The terms vary from six months to several years. A common option is a one-year and three-year warranty period.

The product warranty means free repairs at the manufacturer’s service center throughout the entire warranty period. Upon purchase, a warranty card with the date and stamp of the store is issued, this is the basis for providing repair services.

The buyer is given the opportunity to:

• return goods whose quality does not correspond to the declared one within the first 15 days after purchase;
• exchange the product for a similar one;
• receive warranty repairs during the warranty period;
• return the goods of proper quality within the first 14 days after purchase, if the appearance is not damaged, the packaging and documents are preserved.

The presence of a defect is determined by a service center expert. The defective model is replaced with a working similar one. If the buyer does not want to exchange the product, the purchase amount will be returned.

If the package is damaged (a part is missing), then the seller is obliged to provide the missing elements within three days.

Damage assessment during the warranty period is carried out at the service center. If it is determined that the damage was not caused by violation of the rules of operation and storage, the manufacturer will repair the product free of charge.

The warranty does not apply to the following situations:

• if the product serial number has been changed, removed or damaged;
• if a piece of equipment or an individual part is replaced with non-original components;
• if the manufacturer has changed the design;
• if the cause of the breakdown is improper operation.

DIY photo of tennis tables