Garden furniture made of logs - 45 photos of interesting options

DIY decorative stupa

For the stupa, take a 1 m long piece of aspen or willow log. You can make a stupa with tight-fitting bark or clear it of bark completely.
If you choose the second option, then carry out debarking as carefully as possible so as not to leave traces of chips on the decorative surface. In the upper half of the log, hollow out the middle, leaving the walls 2-3 cm.

It is advisable to reduce the wall thickness along the edges, but this will require skill.

On the bottom, scratch the outline of 3 legs and a 15 cm wide stand and carefully remove the excess wood with a chisel, leaving a smooth cone in the central part. The advantage of this product is its curvature, which gives optimism to the novice master and charm to the stupa.

The advantage of this product is its curvature, which gives optimism to the novice master and charm to the stupa.

Assembly

Log table with dimensions

1. Let's mark the prepared log for sawing. After that, using a chainsaw, we will divide it into the necessary parts. You can do this yourself or hire a sawmill. The services of professionals will cost a certain amount, but the likelihood of damaging the log will be reduced.
2. Carefully cut the logs for the tabletop lengthwise. Make sure the cut is even. The halves of the logs will be positioned with a flat surface up, so they form the table top.
3. After sawing, clean the resulting parts from the bark. This can be done with an ax or chisel and hammer. Carefully cut away the bark, being careful not to damage the surface of the log.
4. If necessary, cleaned logs are processed with a grinding machine. This way you can achieve a smooth surface and hide wood defects.
5. Putting the details together. We cut out a round groove for each log, on which another will lie on top. Try to adjust the size of the groove to the part as much as possible, this way you will achieve greater stability.
6. We connect the folded logs with self-tapping screws. To do this, we make a hole 15 centimeters deep in the top log. Then we place a self-tapping screw in the hole and tighten it with a screwdriver. We connect all the logs in series.
7. We fix the table cover on the resulting stands. This is done using the same screws. For beauty, you can disguise the screw caps with metal caps.
8. We thoroughly impregnate the finished table with a protective composition. Apply three to four coats to best preserve the wood. The drying time of the impregnation is eighteen hours, after which a layer of varnish can be applied.

Labor and cost

Sawing and processing logs is a labor-intensive process that takes from an hour to two. Sawing gutters and fastening logs with self-tapping screws will require skill; this task can also take two hours.

The price of the table will depend on the type of wood chosen. A box of self-tapping screws 6 x 200 in the amount of 500 pieces costs 2.5 thousand rubles. Some stores sell them individually, so you can save a lot of money.

One can of impregnation costs about 600 rubles, depending on the manufacturer. The varnish will cost approximately 200 rubles per 0.2 liter. The funds spent on protecting wood from rotting will result in many years of use of the table.

Beautiful examples

Massive chopped bed. This piece is incredibly strong due to its design. The bed is wide enough and comfortable, so it can comfortably accommodate a couple of people.

Combined set of table and benches. Quite elegant, it has a somewhat lightweight design (in the production of the tabletop and seats, boards, rather than halves of logs, were used). Joining the material in a “paw” type will add reliability and strength to the furniture.

A very atmospheric chopped sofa in the loft style. There is nothing superfluous in this model; the structural elements are roughly assembled, which adds extravagance to it.

To learn how to make a bed from logs with your own hands, watch the video.

Creative solutions in the design of a hunting lodge and furniture for a fisherman

Making a carpentry workbench with your own hands

For each room, be it a gazebo near the house or a bathhouse, we try to create unique interior accents, and we transfer some solutions to rooms for different purposes if we see that our idea will only benefit from this. For example, wooden arches made of logs painted with picturesque landscapes can complement the hunting design of any room.

Also, small coffee tables are suitable for all rooms in the hunting lodge - we often make their tabletops from cut wood; and the legs are made of suvels and burls. All this creates a colorful and impressive hunting design and makes the house truly memorable and atmospheric.

Beautiful examples

You can create furniture for your home and garden yourself. It will be unusual and stylish just because you created it yourself. You can brag to your family and friends. Homemade products will help bring your ideas to life and reveal your individuality. For example, you can knock down frames for armchairs and a sofa from edged boards. Place soft, colorful pillows there, and also lay down a fabric of a suitable color. Such furniture will become the highlight of your summer cottage.

Be sure to find out the exact dimensions of each element so that you can make an original folding chair. It will always come in handy at the dacha. Such furniture can be easily rearranged and moved to the place you need.

When implementing your interesting ideas, do not forget that the models should fit the overall style of the room. Nowadays, the most common sets are those created in a modern or French style. High-tech, country, and minimalist styles are also relevant.

You can often see different combinations of materials. This could be, for example, wood, cast iron, metal-plastic trim. To create a romantic atmosphere, furniture in the Provence style is suitable. It can be made of wood or it can be forged options.

The main requirement for any product is convenience. Rattan structures are often used. They are not only visually attractive, but also quite comfortable and convenient. You can decorate the products with a variety of pillows and fabrics.

You can focus on fashion, but it is better to choose those products that you like. Then the interior items will only cause you delight and positive emotions. The main thing is to follow a single style, adhere to the color palette and not be afraid to experiment.

Now you know how to create furniture for your garden and dacha with your own hands

Don't forget about the most important step - creating a clear outline. Follow it step by step, and you will be able to create a real masterpiece that will delight you and your loved ones

Be sure to prepare the place for work, all the tools and parts, so as not to look for them later. This will help make the work process relaxed and easy. Unleash your talent by starting to create interior items with your own hands.

To learn how to make garden furniture with your own hands, see the following video.

Where is it most often used?

The use of rounded logs is relevant in many stylistic areas of residential decor, as it can be successfully combined with other materials, with many color shades in the decor of walls, ceilings, and floors. But most often such decorative items can be found in rooms with decor in the following styles.

No less relevant is log furniture for a garden house, a gazebo on a summer cottage or a park. But you shouldn’t leave it in the open air for a long time, as precipitation will negatively affect the quality of the surface.

You can complement the beauty of timber furniture with the help of decorative elements made of natural rattan, glass or metal, leather.

Selection of source material

The harmonious arrangement of garden furniture and successful combination with other objects of the surrounding design largely depend on the material of their manufacture. Most often it is recommended to use wood as the main material. Branches, twigs, logs and trunks become excellent raw materials for the manufacture of unique products.

However, not only wood can dominate in the choice of materials for the manufacture of garden furniture. You can do the thing yourself using concrete blocks and metal. Even old car tires can become raw materials for making original things.

Flaws

When using logs and round timber to make furniture, you may encounter some weaknesses.

The disadvantages include:

• Tendency to cracks
  . Due to moisture and temperature changes. Such furniture can shrink, swell, and become deformed;
• High price
  . Yes, you have to pay a lot for natural material. Especially when it is solid wood and not its derivatives;
• Complexity of production
  . The process for making furniture from this type of wood is complex. Hence the cost increases;
• Heavy weight
  . If this is an old house with a weak frame floor, it is better not to install such products here;
• Specificity
  . It is natural, environmentally friendly and safe. But still, not every person perceives such furniture as beautiful and sophisticated. This just scares some people away.

So you need to weigh all the pros and cons, and then make a final decision for yourself.

Set of tables and benches

Photo - a compact combined version of benches and a table, convenient for infrequent movements

The structure will not move, but it will be strong and monumental. It is better to make the legs of the table X-shaped as in the photo below.

The construction of the structure is usually based on the assumption that it will never be rearranged. But it is better to remember that life is unpredictable, such a need may arise one day.

In this case, make the entire structure not from logs and beams, but from boards. The beam connecting the table with the benches should be as low as possible.

Also, the beam should consist of two parallel boards connecting the legs of the table and bench from the outside and inside. Carefully choose the distance from the table to the benches; the closer they are, the more convenient it is to eat at the table, but not the more convenient it is to climb onto it. Please note that this distance cannot be changed. The finished design is shown in the photo above.

Materials

Solid wood furniture is popular. Unlike metal, it is environmentally friendly and safe. As already noted, country furniture can be made from different types of wood. The most popular are conifers. They have healing properties, but are notable for the release of epoxy resin, so the wood should be deresined so that the furniture does not stain clothes.

Buyers often prefer to purchase products made from pine. It can be classified as a soft breed. However, it is not durable enough. However, the products from it will turn out to be the most creative and fantastic. Eucalyptus options are attractive. Larch models will require special care when using such products outdoors.

The most reliable and durable options include products made from hardwoods - yew, birch, dogwood. They contain special oils that protect against the effects of natural phenomena. They will serve you for many years. Teak furniture is also a great option. This breed is resistant to various climate changes. This type of wood is used in shipbuilding. You can distinguish furniture made from this material by the attractive natural patterns on the wood.

If you want to make attractive wicker structures, you should pay attention to flexible tree varieties. For example, these could be bird cherry branches

They are quite pliable, soft and plastic. This will help you show your imagination and create real masterpieces.

Garden furniture with logs at the base will look good. They won't even need to be processed. You just have to cut the appropriate size and install them at the required distance. The table can be made quickly and easily. It is enough to place a thick stump in the middle, build a tabletop, and the furniture is ready. You can use different types of wood.

You can make garden furniture from boards. This particular product has a predetermined flatness and a small thickness. All this allows you to successfully connect the boards together using nails. Using a regular grinder you can sand the product. It is worth noting that in this case you should first create a tabletop. This is done by fastening the boards together. Then you can move on to the base.

Options for children

You can make many different crafts from solid wood, logs or branches of suitable size. Using the recommendations or watching videos on making products, you can easily make a craft with your own hands. There are many simple options that a child can handle.

Simple models can be made together with children. The resulting figures in the form of birds or animals will decorate the interior of the room, and will also benefit the natural landscape. An owl together with a small owlet, a cheerful hare or a sly fox will look perfect on the lawn or in the garden.

To make an owl figurine, you should prepare materials and tools. In this case, you cannot do without wooden rings of different sizes, a hacksaw and decorative elements. You should also consider how the parts will be fixed. They can be glued or nailed with small nails. This decor can be called street decor, which is why a log will be used to secure the bird.

Progress.

• It is necessary to take saw cuts (2 pieces) of different sizes, for example 20 and 14 cm. Fix them vertically.
• Prepare blanks for the eyes. For these purposes, small saw cuts (4 pieces) are used. They are nailed or glued to the top of the base.
• Now you need to take two rings and saw them to make wings for the owl. You can also not saw the circles, but use oval-shaped rings.
• All that remains is to decorate the owl, giving it a natural look.
• If desired, the bird is decorated with feathers and buttons are used to decorate the eyes.

Materials for making furniture: our tips will help you make the right choice

The choice in favor of wood is made due to the advantages of this natural material:

• Durability. If you follow the production technology and form a protective layer, you can guarantee a long service life of products made from solid wood. By following certain recommendations for caring for a wooden surface, you can use a table or chairs for half a century;
• Presentability. Products create a special atmosphere, becoming the center of attention of others;
• Naturalness;
• Ergonomics. When developing furniture sets, the characteristics of specific people are taken into account;
• Maintainability;
• Choice of finishes;
• Uniqueness. No one else will have exactly the same furniture.

The manufacture of wooden furniture is most often made from wood panels, which can be:

• Solid, made of solid wood;
• Glued or pressed. In the production of such shields, thin wooden sheets are securely connected to each other, forming a complete material.

To make furniture with your own hands from furniture panels, you can use materials of different colors. In the manufacturers' catalogs you will find wood in light and dark colors. This will allow you to choose the appropriate option for a specific interior.

Furniture panels come in different colors

If the cost of ready-made panels seems too high, you can make furniture with your own hands from improvised materials. In this case, you will have to show some imagination so that the found branch, snag, bough or pallets left over from building materials become part of the future product.

A bed made from improvised materials can be beautiful

In an effort to reduce the final cost of the product, some make their own furniture from chipboard. In a certain situation, this option deserves attention, but you should not count on the long service life of the finished set or table. This is an economical option that is suitable for a country house. It is not worth moving such products from one place to another.

Chipboard should be used carefully

To make furniture from solid wood with your own hands, you can use wood of various species. Please note that it may be:

• Solid. Suitable for the manufacture of load-bearing elements. It could be an apple tree, beech, oak, sycamore, elm and many others. Elements made from such wood can withstand significant operational loads;
• Soft. A suitable option for the manufacture of finishing or ornamental elements. Using cedar, poplar, birch, pine, willow or alder, you can get a product with a fairly beautiful texture. Due to its plasticity, the product lends itself well to processing, allowing you to form an element of the desired shape and size.

Wood may vary

When choosing a type of wood, you should also focus on the texture and texture of the material. A smooth tabletop can be made from beech, linden or birch. When using walnut, blanched pine, oak or ash, you can achieve some relief.

The appearance is determined by the wood texture

When deciding to use an array, you should make sure of the quality of the material in advance. It should be:

• Virtually no knots, which significantly reduce the strength characteristics of wood;
• With a tight fit of annual rings. This is especially true for coniferous trees. The closer the rings, the stronger the board will be;
• No fungus. Its presence is indicated by the uneven color of the wood. Especially in the cut areas.

Before starting work, you should ensure the quality of the material

Features of making wooden furniture

Before you start producing wooden furniture, you should prepare the necessary tools, equipment and materials. It is worth making sure that you have a woodworking machine that allows you to create a surface of any shape and size. This will allow you to implement any project you have in mind.

The manufacturing process itself includes the following steps:

Project development

It is important to consider where and how the future product will be used, its size and shape. Drawings of all elements for the future product are worked out in detail. Marking

At this stage, drawings from paper or electronic media are transferred to wood. Sawing. All elements are cut to size. Treatment with special compounds, the characteristics of which depend on the location of future use. It is advisable, in addition to biosecurity, to provide protection from moisture. Application of decorative coating. This could be varnish or paint. Assembly. The elements can be connected using adhesives, slats, and dowels. It is possible to use other technology.

Furniture assembly is a critical stage

Manufacturing technology of a standard bed

Making a solid wood bed with your own hands is carried out in several successive steps:

1. Preparation of necessary tools and materials.
2. Carrying out calculations of the quantity of required consumables and their sizes.
3. Pre-treatment of lumber.
4. Making the frame.
5. Assembling and installing the back and legs.

The final stage of work is treating the finished product with protective solutions, as well as decorating the bed.

Installation tools

To create a bed from logs, you will need the following tools:

• Roulette;
• Pencil;
• Construction corner;
• Level;
• Screwdriver;
• Axe;
• Plane;
• Bit;
• Grinder machine. The tool can be replaced with sandpaper of various grain sizes;
• Chisel;
• Mallet;
• tongue and groove;
• Hex key;
• Jigsaw;
• Electric drill.

To make a bed from logs you will need a jigsaw.
Also, to work with boards you will need a hacksaw.

Calculations

To calculate the required amount of consumables, as well as the dimensions of lumber, it is necessary to draw up a drawing of the future structure. In this case, a ready-made detailed bed diagram can be used. Using it, the parameters of the product can be easily changed proportionally, thus achieving the required dimensions of the bed.

The diagram must indicate not only the dimensions of the future bed made of rounded or chopped logs, but also the attachment points of the combined elements. For complex structures, it is recommended to create drawings of the future product in different projections.

To calculate the dimensions of the bed, you can focus on the dimensions of the existing mattress. It should be taken into account that a comfortable sleeping place is one that fully accommodates the width of a person with his hands clasped in the abdominal area, and at the same time there is a margin of 20-25 cm from the elbows to the edge of the bed or sleeping place.

Material pre-treatment

Before starting work on creating a bed from chopped solid wood, the lumber must be additionally processed. Pre-finishing of the material consists of the following procedures:

1. When purchasing solid logs, the bark must be removed from the lumber. This is done using a mallet and chisel or an ax. The bark can be left only in cases where it shows no signs of damage. Such logs cannot be sanded, but are only thoroughly impregnated with stain in 3-4 layers and covered with varnish. However, the use of beds made from bark logs often results in injuries. Therefore, it is still better to remove the top layer of wood.
2. Sand the logs using medium-grit sandpaper. In this way, the top layer of wood is removed, renewing it after storage in warehouses. This stage also allows you to further smooth out the unevenness of the lumber and prepare the wood for deep impregnation.
3. Impregnation of lumber with stain. When using the solution, not only the wood is painted in the desired shade, but also its additional disinfection.

Be sure to remove bark from whole logs

Both rounded and chopped logs can be used to make a bed. Boards are used as additional lumber when creating beds from solid wood.

At the end of the preparatory stage, the logs are trimmed to the required dimensions. If you plan to make a massive bed from beams, semicircular cuts are made at the ends of the logs, allowing the rounded elements to be tightly placed on top of each other.

Frame making

When creating the frame of a classic standard bed 2x1.6 m from solid wood, you will need logs 2.2-2.4 m long, with a trunk diameter of at least 20 cm. You will also need boards 10 cm wide and 2.5-cm thick. 3 cm. The boards must be cut to a length of 1.6 m. They will be needed to create support for the mattress.

To install a support under the frame, you will need beams that will be attached along the inner perimeter of the frame, and one supporting central board.

An example of a log bed frame

The assembly of the frame from the beams occurs in the following sequence:

1. On a hard surface, 4 logs are laid out in the shape of a rectangle of a suitable size, 2 of which have cuts. The elements are connected to each other with dowels or self-tapping screws.
2. Along the inner perimeter of the logs, at the same level in the middle, a support beam is fixed using self-tapping screws.
3. In the middle of the frame, at the same level, parallel to the side logs, a support board is fixed.
4. Perpendicular to the sidewalls, boards are laid on the supports, which will serve as lamellas. They are fixed to the supports using self-tapping screws.

The optimal distance between the lamella boards is 4 cm. Instead of boards, you can also use a solid sheet of plywood. However, in this case the structure will be much weaker.

Attaching the back and legs

The backs and legs can be attached to a bed made of logs as separate elements, or built onto a frame. To make the backs and legs separately, a pair of logs are placed vertically at a distance of 1.6 m from each other. From above and 10-20 cm from the floor they are connected to each other perpendicularly by beams or logs. The elements are fixed using self-tapping screws.

For greater structural strength, the perpendicular elements of the backrest can be additionally equipped with stiffening ribs, in the form of thin beams or rounded logs. The second headboard is made using the same principle. If desired, it can be built of the same or less height. The backs with legs are attached to the frame using self-tapping screws in several places.

When adding the back and legs to the bed body, 2-4 logs are used as the lower support and 1-3 elements for constructing the frame. To extend the legs, 2 logs are connected using dowels. The bed frame is turned upside down and connected logs are fixed along its edges. After this, the structure is turned over to its normal position. At the same time, the legs extended along the edges should look like a continuation of the frame.

Finished log bed with legs and headboard

The back is made according to the same principle. Holes for dowels are made in the logs in the legs and at the head, and additional logs are fixed on top of them. For strength, such connections are additionally fixed with wood glue, which fills all the seams of the structure.

After assembly, the structure must stand until the glue completely hardens. Only after this can you begin the final finishing of the bed.

The final stage

After assembling the entire structure, the logs must be sanded with medium or fine-grained sandpaper. A grinder with an abrasive wheel of 140-220 microns is also suitable for this work. After processing, the wood is impregnated with a colorless or tinted stain. When it dries, the product is coated with varnish.

You can add shine to your bed in another way. The wood is coated with teak oil in several layers, and then treated with furniture wax and carefully rubbed with a leather grinding wheel. With this treatment, the tactile sensations when touching the bed will be much more pleasant.

Types of designs

Drawing of a garden table
One of the popular options for garden furniture is a gardener's workplace. Even if you are not an avid gardener, without a well-equipped table it will be much more difficult for you.

If you prefer original solutions, you can make a picnic table in an unusual style.

Folding garden chair

On a fine summer day, a gazebo with folding chairs and a table, which are not only comfortable, but also compact, will be indispensable. Bright modular structures, such as benches, will add variety to the landscape. During frequent family vacations, do not forget to take care of the kids and make a table and chairs of a suitable size for them.

Drawing of the future cabinet

The design drawing is of great importance for all further stages of product creation. It is compiled taking into account the size of the closet itself and the layout of the apartment. The purpose of the cabinet also matters in choosing a model and working out the details of the drawing. If you need a cabinet, for example, for tools, you should make it wider and lower, and if for books - high and narrow. Next, you need to decide on the number of shelves and compartments, and for this you need to know what will be stored in the closet.

The cabinet has a unique design.

Of course, it’s unlikely that you’ll be able to do everything perfectly the first time.

After the cabinet model has been selected, it is necessary to transfer its plan to paper and depict it in the form of a drawing. First, the frame of the future product is designed, the dimensions of the walls, doors and bases of the cabinet are indicated. Then you need to depict the shelves and the internal components of the product, indicating the length and width.

It will help place all the necessary things in the room, and with its originality will add a touch of extravagance to the living room.

Today, about 40 types of wood are used to make furniture, which have different characteristics.

How to collect?

In order to make the process of assembling garden furniture as easy as possible, we recommend stocking up on all the necessary tools in advance. Professional jigsaws and planes in stores are quite expensive, so if you plan to assemble one bench and settle down there, then it is not advisable to purchase them for personal use - ask your country neighbors or friends.

The process of making furniture will be much easier if you find the necessary instructions or drawing in advance. Once you gain experience, you can easily improvise and create your own unique projects. But in the initial stages, it is better to stick to proven schemes.

Chopped dog kennels

If your dog lives in the yard, then she simply needs shelter from the scorching sun, rain, wind and snow. After all, she, like a person, needs a place to rest and sleep. Sleeping on the ground or hiding under a bush during a rainstorm is not only unpleasant, but also harmful to a dog’s health. That is why log dog houses are the only correct solution in such a situation. By purchasing a log cabin for your pet, you not only keep him healthy, you also add a beautiful decorative element to the area.

Kennel for the dog “Baby” Art: 012 Price: 19,000 ₽

Buy online

Dog house “Terem” with architectural cuts of the end of the log Art: 013 Price: 20,000 ₽

Buy online

Large dog house “Caprice” with an extension under the porch, chopped from a log Art: 014 Price: 30,000 ₽

Buy online

We weave balls from branches to decorate the garden

Decorative balls of different diameters, woven from willow branches, look amazing on a personal plot. The weaving process is quite simple:

1. First we create a frame for the future ball. Take a branch and bend it in a circle several times. We fix it with wire.
2. By what method do we create a second circle of slightly smaller diameter (so that in the future it can enter the first circle). Then we also form the third circle.
3. We insert the circles one into the other and separate them from each other at 90 degrees (as in the photo). We fix their location with wire.
4. We begin to wrap this frame with branches until you give your structure the appearance of a ball. In this case, branches should be passed not only at the top, but also woven into others to add rigidity. If necessary, strengthen the branches with wire.

Balls can be created in different diameters for further use in the garden. How and where to place your branch crafts is up to you. They can be placed on the ground or hung from a tree.

Care

In addition to watering, there are two other activities that should be kept in mind. It's rain and wind. In a homemade flower garden, the volume of soil is small, so until the plants reach the required root size, the flowers need to be protected from heavy rain. The soil in the flowerbed is usually covered with small shavings and wood chips, which prevents the soil from being washed away.

The second problem is weeds, which need to be removed in the first weeks of warm weather. If you start a flowerbed, the flowers may not gain the necessary green mass

For hanging plants, it is important to regularly trim the tops, otherwise the process of uncontrolled moisture loss will begin.

Pair of romantic armchairs made of logs

The happy owner of a log from a log house, as a rule, does not know what to adapt it to. But you can turn it into two good-quality chairs for gatherings with your wife by the fireplace.

We saw off four half-meter logs from the log - these are the legs. Another piece, up to a meter long (as convenient) needs to be split in half lengthwise - these are the seats. We place the legs in pairs parallel to each other and attach the halves of a long block of wood to them with the flat side up. The backs and armrests are made from beautiful thick driftwood. Don’t forget to coat our new furniture with anti-rot and anti-bugs protection.

Wooden chairs

Schemes and drawings

Before realizing your idea and creating the necessary furniture for your dacha, you should definitely draw a diagram and drawings that you will use. It is necessary to strictly follow what is written so that the product turns out to be of high quality and reliable.

With patience and skill, you can make a garden bench. It will be a good option for relaxing for the whole family in the garden. Assemble all parts as indicated on the drawing.

It’s worth starting the process from the legs. Parts A and B are attached first, and rail D is attached to them to support the seat. Then part E is attached. Connect all the slats with bolts. The opposite leg should be assembled in the same way. Then part C is connected. Finally, the strips F should be secured. You should leave a gap of about one centimeter between them. Coat the finished product with varnish. This should be done in two layers. Don't forget about sanding. Such country furniture will delight you and your whole family every day.

You can create a picnic table with your own hands where a group of friends will gather.

It is worth noting that the dimensions of the parts can be adjusted depending on your preferences. They should be attached to special bolts for furniture. You can also use nuts and screws. To make the structure look more attractive, you should screw the bolts on the inside of the table or bench. This way they will not spoil the appearance of the product. The created model will also require sanding and varnishing.

A folding chair in the country will be very useful.

It is quite comfortable and does not take up much space. You can put a child on it. You can easily move such a product to the place you need. A transformable chair will help add originality to your space. Moreover, this option will also save space and your finances. Outdoor furniture can have the most creative designs, or it can be made in an antique style. Kitchen furniture is also relevant.

If you have children in your family, then you should think about a children's corner. You can make an interesting swing and please your kids. You can also successfully place a sun lounger on your garden plot, where you can relax and sunbathe on sunny days.

Bench with backrest with tongue-and-groove joints

The next project is an outdoor wooden bench with a backrest. It has a fairly strict appearance and will become a functional decoration in any garden or dacha. The vertical slats of the back give the massive structure visual lightness. Shaped armrests and a curved top bar add Japanese influences to a clean, classic look. It is simply created for carefree contemplation on shady alleys, and will look even more expressive surrounded by greenery and flowers.

If in the previous two projects we talked about how to make benches using simple carpentry joints, then here we will talk about the classic tenon-socket connection. It underlies all design elements of the project. You will have to make a lot of spikes and nests, so it is advisable to think about optimizing this process in advance. The simplest and most affordable option is to use a hand router and a saw table.

Advice! For accurate and quick selection of slots, use a homemade milling template with slots of the required sizes.

Drawing of a bench with a wooden back

Advice! Decorative antique finish perfectly complements the simple design of this wooden bench with a backrest. Use the brushing capabilities to texture individual structural elements - the top crossbar, the middle backrest and armrests. The combination of smooth and aged surfaces will create an original design contrast.

Prepare the details

According to the dimensions specified in the drawing, make the main parts of the bench. To quickly apply markings, use pre-prepared templates. Duplicate parts can be mass produced. After cutting, fasten all the identical parts into a pack and process their ends with a sander, this will significantly speed up the work process.

Make spikes

On the saw table, form tenons on all tenon pieces, following the dimensions from the diagram. Using a groove disc will make this job much easier. This can be done no less carefully with a regular saw blade, followed by trimming the waste with a chisel, as shown in the photo.

Mill out the sockets

Assemble the sidewall

Perform dry assembly of the sidewall. If the joints in the structure are not tight enough, fine-tune them using one of the methods we discussed in the article “Perfectly Fit Joinery Joints.”

Carry out sequential gluing of the structure

After checking the accuracy of the fit of the connections of the entire bench, proceed to sequential gluing of the base elements first, and then the back. After the glue has completely dried, attach the seat strips with self-tapping screws.

Nuances of choice

Log furniture has a number of advantages. However, this rule applies only to those pieces of furniture that are made strictly according to technology using high-quality fittings and fasteners. Saving on components or protective coatings for logs can have a detrimental effect on the durability of structures and will reduce their resistance to the negative influence of external factors. Therefore, you need to choose such interior items carefully, without haste, weighing all the pros and cons.

Let us describe the main factors that cannot be ignored when choosing wooden furniture:

• cost - the process of creating furniture from logs is quite complex, painstaking and cannot be rushed. Only if this condition is met can it be said that the log bed will serve for several decades in a row. That is why interior items of this kind cannot be cheap. A low price should alert the buyer, force him to carefully inspect the design for defects, read the accompanying documentation for the product (quality certificate, passport, assembly and maintenance instructions);
• sizes - log interior items often have impressive dimensions, so they should not be selected for narrow spaces with poor lighting. In small rooms they will look overly bulky and will weigh down the space. And for large spaces, such furniture is simply a godsend;
• surface aesthetics - the logs used in the manufacturing process of the furniture structure should not contain knots, chips of the interlayer in the wood mass, and the annual rings should be located as close as possible. These factors will indicate the high quality of the material used. If the bed does have such shortcomings, its price should be significantly reduced.

Taking these factors into account, you can choose successful models of tables, chairs, beds or cabinets made from rounded logs and profiled logs for your home or cottage

Types of products

Furniture made from logs is very relevant for many premises. In its manufacture, different types of wood are used, so the operational parameters may vary.

Conventionally, experts divide all wood species used in the production of log interior items into two types:

• made of hard wood: maple, oak, ash, walnut. Such species are relevant for the manufacture of furniture that experiences the highest load during operation. For example, a bed frame, a dining table top;
• from soft wood: poplar, willow, pine, spruce, chestnut. These types of wood are used for the manufacture of decorative elements when decorating log furniture. For example, facades, carved decorations.

We also note that furniture made from solid logs will be more reliable, durable, and more expensive than options made from laminated veneer lumber.

The appearance of log furniture may also be different, which is a consequence of the use of different compositions to give the item high resistance to impact:

• painted - to decorate wooden furniture, various types of coloring compounds are used, which can completely cover the natural pattern of the wood or slightly shade it. This ultimately determines the external aesthetics of the item;
• varnished (matte, glossy). Varnish with a gloss effect allows you to add clarity and brightness to the wood grain. Such surfaces are perfect for classic interiors. And matte wax gives the surface a special charm, relevant for country, Provence and other areas of residential decor.

Adviсe

Garden chair from a stump
In order to make a piece of furniture from scrap material, an old barrel will help you, which will later become an unusual chair with a back. In a short time, you can build a bench using boulders as support legs and a wooden board as a seat. To build such a bench you will need the following tools:

• planer for processing boards;
• drill with a diamond attachment;
• anchor bolts.

Having processed the board using a plane, they adjust the boulders to the required height, after digging a hole and arranging a sand cushion at the bottom. It is necessary to drill holes in the board and stones for anchor bolts.

The final step is to tighten the bolts and cover the surface of the board with a protective layer of varnish.

Stands

Saw cuts in the form of plates can be successfully used as stands for dishes, vases or flower pots. The simplest craft is a plate 1-3 cm thick. It is better to leave the bark. On top of this item is coated with colorless or tinted varnish. The saw cut can be made in round (perpendicular cutting) and oval (cutting at an angle to the axis of the trunk) shapes. Trunk diameter – from 10 cm.

Branch cuts are also suitable for making a stand. The photo shows a craft assembled from several small cuts. First, a lattice base is assembled from wooden slats. The cut plates are fixed on it, and their center should be located at the intersection of the slats.

Crafts are decorated with various designs. The image is applied with acrylic paints using a brush. A technique accessible to everyone is decoupage. A picture cut out, for example, from a magazine is glued to the cut. You can use a decal. The top of the craft is coated with a special decoupage varnish.

From a small block of wood you can make a simple stand for pencils and pens. In such a log with bark on top, several holes with a diameter of 10-15 mm are drilled into which office supplies are inserted.

Massive flower stands are made from larger logs of more than 50 cm in height. The bark is preserved on them, which is impregnated with a composition against rot and insects. This product changes the shade of the surface of the product. The top cut must be strictly horizontal. It is carefully polished and decorated.

What kind of furniture can be made?

When clearing a garden or other area of ​​stumps or old trees, it is worth finding a more worthy use for them than recycling. Using logs and roots will allow you to make interesting crafts, furniture, and buildings.

Entire compositions are built from them, used for arranging a playground, and variations are created in the form of flower beds. Old logs are also used to make furniture.

Logs are used for construction:

• benches made from a single trunk;
• chairs and benches made of hemp;
• dining table;
• furniture set.

Having experience in working with wood, you can make comfortable and functional furniture for your garden yourself. Even the simplest design requires time, desire, and the availability of suitable professional tools. For furniture production, a log with a decent cross-sectional diameter is more suitable. During the work process, it is processed with an ax, then an electric saw or chainsaw is used to create the basic shape. At the final stage, cleaning with a chisel and grinding is carried out.

Tools

Before carrying out the main work, it is necessary to prepare the following list of tools and equipment:

1. Special impregnation for wood improves the appearance of the material and protects its surface from the appearance of fungus and mold. This is especially true if the table will be used outside in the garden. There is no point in saving on the solution; it is better to take it with a reserve.
2. A hacksaw with fine teeth allows for accurate cuts of workpieces.
3. An ax and a chisel with a hammer are used for removing bark from logs and some other work (grinding grooves and finishing small recesses).
4. A chainsaw is considered one of the main tools when working with wood. With its help, you can cut logs both longitudinally and transversely.
5. A screwdriver allows you to carry out work far from a power source.

Additional consumables you will need are self-tapping screws for fastening the parts into a single structure and transparent varnish to create a protective layer on the surface of the furniture.

Recommendations for masters

To ensure that wood furniture pleases you for a long time, there are some tips that should not be neglected:

• Be sure to protect wooden furniture from precipitation and temperature changes. For this purpose, you can find special solutions and compositions in stores.
• Be sure to treat all corners and surfaces that come into contact with the body. This way you will protect yourself from splinters and other injuries.
• Don't neglect drawing up a drawing. This will help you calculate the amount of material and think through all the details.

After watching the video, you will learn how to make a table from a log with your own hands.

https://youtube.com/watch?v=MEr4bSXiDK8%3F

Advantages

Before you buy log furniture for yourself, or try to make it yourself, some additional information about such products will not hurt.

Outwardly, she is rough and massive. But that's the beauty of it. Chopped wood and round timber help create a unique feeling. Here, in many ways, one of the main advantages opens up. In general, the advantages include the following points:

• External attractiveness
  . Even in the photo she looks gorgeous. Imagine how lacquered oak furniture will look, which was simply cut down with a chainsaw, the bark was removed and the naturalness was emphasized;
• Environmental friendliness, safety and odor
  . Even if it is garden furniture, it will emit unique aromas. They have a beneficial effect on humans. The material is environmentally friendly, absolutely safe;
• Long service life
  . Rounded furniture, coated with antiseptics and varnish, can serve for many years even in garden conditions;
• Easy to care for
  . There are no complex procedures involved in the care process. You can periodically renew the varnish layer. And any damage can be repaired with your own hands;
• Relevance
  . Such outdoor and indoor furniture is suitable for different houses and summer cottages. However, it remains in demand for many centuries.

But it's also worth looking at the other side.

Implementation of unusual ideas

Furniture made on site

To create interesting items for decorating the landscape, you can decorate tables, chairs and benches with beautiful original branches. Such furniture will become a wonderful and appropriate element of the garden exterior and will not leave any of the guests indifferent.

Another option for making a table for a summer house is to use a large cut of the trunk as a support and a horizontal cut of the butt as a cover. The horizontal cut is fixed on a shield made from parts of the trunk. To make the structure reliable, it must be supported with logs, the tops of which have been previously hewn off, and secured to support pillars.

Mills

One of the popular decorations for the landscape has become a wooden mill. If in ancient times people could not imagine their life without it, now this structure is only decorative.

They are used to add medieval chic or create a fabulous landscape in a personal plot.

In addition to their decorative function, garden mills can become quite practical elements. It is used to camouflage hatches, protect water wells, springs and wells from frost in winter and from debris during leaf fall. With the help of a windmill you can easily disguise any unsightly place on the site. Mills can also be used as a place to store garden tools or children's toys.