Toilet stand to increase height stroymagazin77.ru

When it comes to renovating a bathroom or toilet, most people face the problem that the plumbing fixtures' pipe outlet levels change. This occurs as a result of changing the floor level and rearranging equipment. One way or another, in this case the question arises of how to raise the toilet higher. In this article we will give you practical advice on how to deal with this problem yourself at minimal cost.

How to lift a toilet? There are several approaches to solving this issue

To eliminate the problem of incompatible fittings, you just need to use modern adapters. If you are faced with the fact that the axes of the pipeline do not coincide, you should use a flexible hose system or create a new pipe gasket. The level of future placement of your plumbing depends on how well these holes coincide.

To achieve the required matching of pipes, you can use one of three options:

create a new installation location at which the appropriate level will be maintained;
install a wall-hung toilet;
use a system of adapters and pipes.

What can you use to make a toilet stand to raise it higher above the floor?

A regular compact toilet with installation on the floor.
You need to raise it a few centimeters from the floor, what can you use to make a toilet stand?

First, decide how high you need to raise the toilet.

And also decide on the specific reason for changing the height of the toilet.

In some cases, you can do without a toilet stand (we are talking about toilets with floor mounting).

If you missed the purchase of a toilet, and did not take into account that the sewer pipe goes above the toilet outlet, then you can buy eccentrics (cuffs) that can add a few centimeters in height.

Or connect the toilet to the sewer through a corrugation.

If all these options are not suitable, then the supply can be purchased as a finished product, like this

Part-time material, ceramics raise the toilet to a height of 60 mm (6 cm from the floor).

Instead of a purchased stand, you can make a “pedestal” out of brick; after drying, the brick can be tiled.

I bought red solid brick.

Even better, from concrete, we mark the floor, install formwork, reinforce it, pour concrete.

After drying, this concrete stand can be tiled and then the toilet can be installed.

The stand can be made of wood (this is how toilets were installed during the Soviet Union), you need a board of suitable thickness.

If the stand is not high, then plywood will do; I made the stand from plywood 20 mm thick.

Be sure to sand the plywood and pay special attention to the ends.

I do not recommend using chipboard or MDF.

The main thing when choosing a material for making a stand is the height to which you need to raise the toilet.

How to make a toilet a little taller

To achieve the required matching of pipes, you can use one of three options:

create a new installation location at which the appropriate level will be maintained;
install a wall-hung toilet;
use a system of adapters and pipes.

Conclusions and useful video on the topic

One of the options for attaching a plumbing fixture to the floor is discussed in the following video:

Which method of installing toilets is the best is up to the owner of the property to decide where the plumbing is to be installed and secured.

However, when choosing a technique, it is recommended to take into account the possible loads on the toilet, the material of the device (faience, porcelain), as well as the design features of the toilet room. A careful approach to business will definitely help you achieve the desired result.

Would you like to tell us how you installed the toilet yourself? Do you have useful information and photographs on the topic of the article? Please write comments, share your impressions and ask questions in the block below.

Beginning of work

Before any work, it is necessary to properly prepare the workplace. In our case, everything that is not related to the installation must be removed from the room. It is best to work in a completely empty room. To change the product level you will need:

chisel;
hammer;
wrench;
level;
felt-tip pen;
knife;
screwdriver;
Bulgarian;
sandpaper;
device for pumping water (rubber bulb);
sealant;
cement and sand;
washers, bolts and so on.

Sequencing

Before looking for the answer to the question of how to lift a toilet, you must disconnect it from the sewer and water supply. To do this, you need to turn off the water supply and disconnect the main pipe on one side from the tank, and on the other from the water supply. Next, take care to remove all remaining water from the product. For this you will need a rubber bulb and a regular rag. If you leave even a little water inside, it will definitely spill out during transportation.

In most cases, a floor-mounted toilet is mounted on a wooden base or concrete screed above the flooring surface. It is attached to the sewer in one of the following ways: with a plastic pipe, corrugation or rubber adapter. To disconnect the plumbing from the sewer, you need to remove the pipe or remove the corrugation. If you cannot complete these steps, then simply cut off the unnecessary parts, turn the four bolts at the base and remove it. If the bolts do not come out, then you will need a hammer and chisel. Using gentle movements, break up the concrete or cement coating under and around the toilet. You can also use a drill or hammer drill, but you should be extremely careful.

Next, clean the inside of the pipe that remains from the old seal and dirt. After cleaning, cover it with a plastic bag. This will eliminate the possibility of construction debris getting inside, as well as the release of an unpleasant sewer odor. Now remove all debris and remnants of old materials to prepare the area for installing the plumbing at the new level.

Taking it to the next level

Select a location for installation. To begin with, the product is placed on wooden blocks to ensure that it is taken to the next level. Make sure that the product is horizontal. To do this you will need a building level. It is best that the axes of the sewer hole and the toilet drain pipe coincide. If you cannot line up the matches perfectly, then use adapter flexes. Next, remove the toilet and measure the thickness of the pads to create a new level for the plumbing.

Workflow Description

The first step is to prepare a work area for faucets and other items. The main thing is to get rid of everything that will interfere with the installation of the device.

The technology is typically used as follows:

The toilet and water supply system are disconnected from each other. The water supply to the device tank is shut off. Be sure to close the central valve and remove the hoses from the float on the tank.
The remaining liquid is removed from the device. A rag with a rubber bulb will help you deal with this. This is also required for the bathroom faucet.
The mount is removed from the sole of the device. Screeds made of concrete or wood are most often used. Use a chisel and hammer to remove the fasteners if this cannot be done by other means.
You can disconnect the device and the sewer from each other. The outlet is disconnected from the pipe.
The old cement covering is removed.
The pipes require complete cleaning of contaminants.
The next step is to raise the floor to the required level. In the location chosen by the owner, the toilet is mounted on top of wooden blocks. The building level helps to understand how horizontal the surfaces are. It also helps when the gasket is replaced with an analogue one.

The best choice if the axes do not align exactly is a flexible accordion with a plastic base. Sometimes rubber corrugation becomes a worthy replacement. Using two pipes, normal adapters are created. But then you will have to ensure normal sealing of the joints.

At the final stages, the toilet is fixed to the floor surface. The attachment points are outlined, as is the base itself. Marking increases the accuracy of work. Then all that remains is to drill the holes.

The system is fixed. Cement and sand will be suitable materials to solve the problem. Many people use silicone glue for fastening, but this option is not always convenient. The foam block is convenient only in the sense that it is easy to cut with a hacksaw.

When the work is completed, all that remains is to connect the tank to the water supply.

Wall-hung toilet

Most modern experts recommend using a wall-hung toilet to change the level of the structure. It can be done in two ways:

using the installation system;
creation of a concrete base.

The installation system involves fixing the toilet in a special structure, with which you can adjust the level of the device and then fix it.

This way you can accurately adjust the correspondence between the holes of the toilet drain pipe and the sewer pipe. After you secure the system at the required level, you can hide it with sheets of drywall, choosing any coating for this.

To make a concrete base for a wall-hung toilet, you will need:

two steel studs (thread - M20, length - 80 cm);
wood screws;
material for base formwork (plywood or board);
concrete solution;
nuts and washers.

At the beginning of the procedure, you should install a transition coupling between the toilet and the sewer. Next, carefully select the location of the studs for fastening. Studs should be installed into holes in the wall. It is best for these holes to be through. Otherwise, glue must be used. For the formwork you need to create three planes - two side and front. This is where plywood or board will come in handy. Fastening pins hold the formwork to the wall. In the future, they will serve as a support for the wall-hung toilet.

Now you need to try on the wall hung toilet to check the stud holes. To prevent debris from entering the sewer, place plastic bags over all openings. Concreting the formwork must be done gradually. This way you will eliminate the possibility of the drain coupling moving from its axis. The formwork must hold the structure for at least a week until the concrete has completely set.

Now all you have to do is secure the wall-hung toilet to the studs. Do not forget to treat all toilet and sewer connections with a special construction sealant.

As it becomes clear, you can find the answer to the question of how to lift the toilet yourself. If you have ever encountered a similar problem, share your comments with the readers under this article.

Basic ways to raise the toilet higher above the floor

Raising the toilet above the floor level is carried out in several ways:

Creating a new place to install a toilet with the appropriate level is a complex process, involving a partial restructuring of the apartment's engineering system.
Installing a new hanging-type product is a common solution to this problem, which requires additional installation, possible restructuring and dismantling of sewerage systems.
Construction of a pedestal is used less frequently, as it requires certain skills in finishing work, special materials and dry mixtures (if the podium is made of cement or concrete). The task can be simplified many times if you use foam blocks for the podium.
The use of special plastic gaskets is a frequently used option, which is chosen due to ease of functionality and installation, availability and popularity. Suitable for cases when it is necessary to temporarily create a certain height of the toilet due to the physical characteristics of a person (for example, children, elderly people, disabled people living in an apartment with other residents).
Using pipes and adapters - just like in the first option, you will have to spend a lot of time and effort on carrying out plumbing work to connect pipes and change the utilities in the apartment.

House

The house is a curious form of country toilet, allowing for a wide variety of design delights. In comparison with all the other forms listed above, the house seems to be the warmest and most comfortable option. In addition, it is characterized by increased strength, and the costs of land and materials are the same as when building a less warm and comfortable birdhouse.

6 drawings of a country toilet of the “House” type

There are also such drawings. Using this scheme, we managed to assemble a toilet for only 7,500 rubles. How? See the construction progress and results here

Also, a country toilet, depending on the area it occupies and the features of the construction, can be either single or double.

Example of a double toilet

Attached to a garage or any other building are more complex toilet structures that are not so often in demand by summer residents.

Plastic toilet seats and spacers to increase height

A simple and affordable way to raise the level of the toilet. There are children's stands that will help a small child sit on a large toilet , as well as classic adult ones - for the elderly and people with disabilities .

How do they look

The stand is a frame with a seat of the desired shape and height . If necessary, it can be equipped with a step. In some cases, a special type of attachment is used, which has a more complex shape and a separate adjustment system.

Photo 1. Children's stands, which will help a small child sit on a large toilet, are often sold as a set of a seat and a step.

Advantages and disadvantages

The advantage of the stands is that there is no need to dismantle the plumbing . They are suitable for models of all types and shapes. Stands are used in cases where people living in an apartment need different levels of toilet height. With the help of pads, you can easily change the height and configuration of the toilet seat , and also significantly increase the level of convenience and comfort for each family member.

The only disadvantage is that more complex linings with handrails or steps can take up additional space in the toilet room .

How to install

Installation of the attachment depends on the type of structure. The general principle is that the product is placed on or above the product bowl . The person using it will need to sit not on the toilet itself, but on this stand.

In general, the installation process is quite simple and the user will only need to study the instructions that come with the product.

Sanitary standards

What does the law say? Construction, sanitary and hygienic norms and rules establish a number of restrictions related to the transfer of plumbing fixtures. Damage from leaks and noise should be kept to a minimum.

The following rules help you figure out how to lift the toilet under any circumstances.

Bathrooms should not be located directly above living rooms and kitchens. This is only permissible for apartments on two levels. Thanks to this standard, the lower rooms are protected from possible flooding.

The size of bathrooms and kitchens cannot be changed at the expense of rooms located nearby. That is, the area of the bathroom can only be increased if it is combined with a bathroom. You can attach parts of storage rooms and corridors.

If the standards are still violated, then additional waterproofing for the premises becomes mandatory. Waterproofing is applied to the walls no less than 30–40 centimeters. Then the joints delimiting the rooms will be protected.

How else can you raise the toilet higher: a pedestal

Installing a pedestal for the concept of a toilet involves dismantling the plumbing fixture and then placing it in the same place, but only at a slightly higher height.

What can it be made from?

Often pedestals are made from cement and concrete mortars . In addition, there has been a tendency to make pedestals from foam blocks. This method is the easiest to implement.

Photo 2. Before building the pedestal yourself, in order to avoid mistakes, you need to measure and transfer the contour of the lower part of the toilet.

How to install it

To begin with, calculate the height of the rise and select a foam block in size, from which the base of the future podium will be formed. Then the toilet is disconnected by removing the corrugated pipe leading to the sewer and unscrewing the bolts that secure the device to the floor.

Important! The toilet is disconnected from the water supply and sewerage system. Before doing this, you need to turn off the water .

The contour of the lower part of the product is outlined on a piece of foam block of a given height. Then the part is cut out and applied to the base for comparison. I process the edges of the workpiece until smooth. The finished element is glued to the floor. After the glue has dried, the toilet is placed on the resulting podium and secured with dowels. The edges of the pedestal are aligned under the toilet so that the structure does not look like an alien element, but looks harmonious as a natural extension or part of the plumbing.

Attention! It is important to align the edges as much as possible so that the pedestal merges with the toilet. Subsequently, if this is not observed , the appearance of the unjoined edges will attract attention.

Podium

The podium is not only reliable and extremely durable, but also beautiful and aesthetically pleasing. There are no secrets or know-how in how the toilet is attached to the podium. The installed toilet is checked to ensure there are no leaks or problems with drainage. Then take any sealant or light installation plumbing adhesive and use it to treat the areas where the bathroom comes into contact with the floor. Next, to the desired height, the height under the toilet rim is taken as standard, a podium is laid out of brick - they are attached to each other and to the floor with cement mortar. The surface and sides of the podium are decorated according to preference with tiles, tiles or mosaics. Such fixation can withstand weight up to 400 kg.

What is better: install a traditional model or immediately choose another?

There are different options available to raise the toilet to the desired level. All methods are relatively simple to implement , so almost anyone can cope with them.

If a large-scale renovation is underway at home and you need to save bathroom space , then pay attention to hanging options that can be installed at the required height . It is worth noting that such devices require installation. If the structure of the wall allows such a restructuring, then this option will be more acceptable and convenient .

How to lift a toilet yourself

When, as a result of a back problem, it is difficult to sit on the toilet due to the standard height, the question arises of how to raise the toilet higher. In this article we will give practical advice on how to raise a toilet with your own hands and available materials.

Before dismantling the toilet and preparing a place for a new installation, it is necessary to determine the lifting height. To do this, we place improvised objects on the toilet and determine the height of the rise. We disconnect the water supply and sewer lines from the toilet, turning off the water. Remove the remaining water in the toilet with a rag. The toilet is fixed to a wooden stand using self-tapping screws. The outlet from the toilet to the sewer is made of a corrugated adapter. To disconnect, tighten the corrugated pipe. Unscrew the bolts and remove the toilet.

Do-it-yourself toilet lifts

We carefully place the toilet on the foam block and trace the lower contour with a marker. Then, using a hacksaw, we cut out our stand in the foam block. We try on the resulting blank and sand the unevenness so that it looks like one with the toilet.

Now let’s prepare the base for installation by clearing the area of dust and leveling the surface for the toilet. Having tried on the workpiece, apply the adhesive to the floor and wait one minute to fasten the part to be glued. We remove the remaining glue and, using a level, level the surface of the podium. Let our structure dry according to the instructions for the adhesive composition. After complete hardening, we try on our toilet bowl and mark the hole, Drill a nail under the dowel for fastening. Apply sealant to the sole of the toilet bowl, install and fasten it using self-tapping screws. Then in the reverse order as we took it apart. We putty the podium using drywall putty, and we can paint it the color of the toilet. This design is reliable and does not spoil the appearance.

Posted 4 comments

All of the above methods for raising the toilet can be easily done with your own hands. But if a person does not have time to do this or does not know how to do it, then it is better to call a plumber. True, in this case the financial costs will be much higher, but the quality of the work will also be higher.

I need to raise the toilet by 10-12 cm, which is in excellent condition, and the described method tires me out, but I am 80 years old and my husband is disabled. We cannot do this ourselves. Please send a master who will do this work for the appropriate fee.

First stage: choosing options

In order to raise the toilet a little higher, you need to align its outlet with the outlet of the sewer pipes. This can be done in several ways:

Use a flexible plastic accordion. This will allow you to install the toilet at any desired height, but the reliability of the entire system will depend on the quality of the plastic accordion, and the device itself will be moved slightly forward, which is not always convenient for small toilets.

After a person decides and chooses the most suitable of these three options, he needs to prepare tools, devices and materials, and then begin to implement the plan.

Note to installers: useful tips

Plumbing fixtures are made from strong but fragile materials. Therefore, when securing a porcelain or earthenware appliance with screws (bolts), it is not recommended to use maximum force to tighten it. Be sure to use soft gaskets (silicone, rubber, plastic), placing them under the screw heads.

Attach the toilet to the metal screws carefully, using moderate force. It is strongly recommended to use spacers made of soft material under the screw heads.

If glue is used for fastening, the quality of cleaning and degreasing of the bonded surfaces is of great importance in achieving joint strength.

When using epoxy resin, it is necessary to strictly observe the ratio of resin and solvent during the preparation of the adhesive mass. The glue must be applied evenly to the surface, preventing the formation of air cushions.

When installing the device “on taffeta”, it is advisable to choose strong wood as the material. You can use multi-layer plywood, but in any case you should provide high-quality waterproofing for the taffeta. A humid environment dramatically reduces the durability of any wood.