Bathtub fittings: overview of types of drain-overflow systems + step-by-step installation instructions

Modern innovations also have an impact on the field of plumbing, where many interesting new products have recently appeared. One of them is the bathtub trim, which is also known as the “drain-overflow system.”

Initially, such devices consisted of two separate elements: a siphon and an overflow tube, the installation of which was carried out independently of each other. These parts were later combined into a compact design.

Installing a drain and overflow is not particularly difficult - any home craftsman can do the job. But first you need to decide on the type of strapping and become familiar with the technology of its installation. You will find all the necessary information in our article.

We outlined in detail the features of different models of plumbing fixtures, provided practical advice on choosing a fitting, and also prepared step-by-step instructions for installing the system on a bathtub.

Operating principle and design of the device

A standard bathtub fitting is essentially a more complex design than a regular siphon. It comes with a special tube and controls that are attached to the overflow hole.

Thanks to the pipe, excess liquid is drained into the siphon, which prevents the bath from overflowing and water overflowing.

This system eliminates the need to close the drain hole with a plug. It also allows you to adjust the outflow of liquid so that its amount is equal to the volume of incoming water. This allows you to take a bath while basking in running water.

The drain-overflow system also makes it possible to control the outflow of water. To do this, a rotary handle is mounted on the overflow hole, connected by a small metal cable to the drain valve, which is installed in the lower siphon.

By turning the handle in different directions, you can adjust the tension of the cable, which in turn affects the drainage capacity of the siphon.

Types of plumbing products by material

Bath trims are produced in a wide range.

According to two fundamental criteria, there are two options for the accepted classification.

• according to the material from which the product is made;
• according to the technological features of the design.

The following materials are used for the production of most plumbing systems:

• high-strength polymers;
• non-ferrous metals/alloys - bronze, copper, brass;
• stainless steel, which is coated with chrome as a protective layer.

Let's consider the features of products made from different materials.

Option #1 - plastic

Systems made of high-strength plastic have the following features:

• long period of operation;
• the material does not collapse even with prolonged exposure to moisture;
• relatively low price;
• ease of installation and operation;
• smooth internal surface that prevents the formation of blockages;
• resistance to modern cleaning products, which often include aggressive chemicals.

At the same time, plastic piping with corrugation has certain disadvantages, the main ones being the excessive fragility of the material, which requires special attention during installation, as well as the softening of the polymer under the influence of hot water.

When installing a polymer waste-overflow on a bathtub, it is important to check the fastening points for the appearance of burrs that may occur when the product is cast. If such defects are detected, they must be removed, since in the presence of such a defect it is impossible to firmly connect all components of the structure

Hot water causes the pipe to deform in places where areas of stress have formed due to improper installation.

Option #2 - metal

Plumbing fixtures made of non-ferrous metals or polished/chromed steel are somewhat inferior in popularity to their plastic counterparts. They are strong and durable, but have a much higher cost.

Modern bath fittings are complex systems that significantly simplify the process of installing plumbing fixtures and control the drainage of water during use.

The disadvantage of such products is also the difficulty of installation: when installing the structure, it is necessary to precisely adjust the parts of the product using special tools.

Metal piping is prone to the formation of fat and other deposits; they can be damaged by active substances (acids, alkalis), which are sometimes added to household chemicals.

↑ 4. Installation

You can install the drain and overflow yourself, but it is important not to forget that the tightness of the bathtub in the future depends on the quality of the work. However, despite all the responsibility, installation of the system can be carried out by a non-professional; you just need to listen to the advice of specialists.

↑ General recommendations:

• Follow a certain sequence in your work;
• Use special sealants to process connections;
• When tightening parts, be careful not to strip the threads;
• All elements must be tightened one quarter of a full turn after hand tightening;
• If you cannot tighten the connection, you need to check whether the nut is level.

Installation begins after the bowl is secured to the support. The bathtub must be leveled and fixed. It is also necessary to leave a height gap between the floor and the tank (from 150 mm or more).

↑ Correct sequence:

• The bottom hole of the bathtub is connected to a tee. In this case, you need to process the connection using a sealant and secure the elements with a screw;
• Next, attach the siphon and secure it with the tee outlet with a nut. A rubber cuff can be used as a seal here;
• The overflow neck is connected to a side curved tube (siphon);
• The process is completed by connecting the siphon to the sewer pipe. For this purpose, a special spout pipe is used;
• During each connection, you should remember to lay the seal.

After installation is complete, you need to check the bathtub for leaks. The bowl is filled with water, then you need to carefully examine all the joints and connections. If drops appear on the surface, tighten the elements more tightly and re-treat with sealant.

Siphon installation video:

Design features of drain-overflow systems

According to technical features, models can be divided into the following categories:

• universal;
• semi-automatic;
• automatic.

The most popular is the first design option, characterized by its simplicity and affordable cost.

Simple universal devices

A characteristic feature of such devices is the well-known chain with an attached plug that closes the siphon drain. Such devices are mounted on standard bathtub models, in which the distance from the center of the overflow hole to the middle of the drain does not exceed 57.5 cm.

In plastic systems, all parts of the device are connected to each other using special clamping couplings supplemented with rubber gaskets. This allows you to mount the structure without any additional tools.

Installation of a universal type system is extremely simple; almost anyone can install it, even without much experience or special skills.

The device consists of four components, namely:

• siphon located directly under the bathtub;
• drain neck intended for the lower hole;
• lattice overlay complementing the previous component; the cover has a recess in which the cover is installed;
• a corrugated pipe that connects the upper overflow hole with a water seal designed to drain excess water to prevent the bath from overflowing.

Such bindings can be made from different materials described above.

Convenient semi-automatic strapping

Such a system differs from a universal one in the mechanism attached to it that allows you to regulate the drainage. To do this, not only a corrugated pipe is installed on the hole located at the top, but also a rotary handle connected by a metal cable to the bottom drain hole.

Moving the handle allows you to control the level of opening of the drain neck, making it possible to adjust the outflow of water without using a special cover.

In such systems, the overflow device is disguised as a control handle for the drain structure, which gives the system an aesthetic and stylish look.

At the same time, the design of the handle of the semi-automatic bathtub trim can be very diverse, namely in the form of:

• decorative valve;
• buttons;
• lever;
• rotary ring.

An important advantage of the design is comfort during use, since the handle is located at the top of the bathtub: the user does not need to bend down to the bottom or even wet his hands.

The most significant disadvantages include the sufficient fragility of plastic parts, which is why frequent breakdowns of the mechanism occur as a result of excessively strong impacts on the control lever

It is worth adding that the installation of the piping, which involves semi-automatic draining, is quite complicated for non-professionals, since it requires certain knowledge.

Automatic bath systems

The functioning of this type of harness occurs without the use of cables and rotating elements. Like the previous device, the machine is equipped with an overflow pipe, while at the bottom of the drain there is a special valve: when you press it, a hole through which water goes into the siphon becomes accessible.

Assembling the automatic harness is quite simple; even a novice master can handle it. However, the device has a significant disadvantage: the pressure valve has a low throughput. In addition, it clogs quickly due to the small size of the hole.

Pressing the lever is quite easy: you can do it with your hand or even your foot. The valve is also secured in a pressed position so that you do not have to hold it until all the liquid has left the bath.

The disadvantages of such products include:

1. Quite a high cost . It is several times more expensive than a conventional mechanical device.
2. The need for unnecessary movements . You can only turn off the drain to fill the bathtub with water for a bath or use the tank for other purposes (for example, for washing) by bending down.
3. Possible breakdowns . The most vulnerable part of the automatic device is the spring that holds the valve and drives it. If it breaks, you will have to completely replace the entire system.

When choosing such products, it is better to give preference to well-established manufacturers in order to reduce the risk of malfunction to a minimum.

Other types of devices

A subtype of the automatic system is a harness that has a filling option. Such models take on the functions of a bathroom faucet. A water pipe is connected to the piping, thanks to which the tank is filled using a mechanism located at the overflow hole.

When choosing a product, it is also important to pay attention to the color (white, golden, black, copper, with ornaments, silver), as well as the design of the product: heavy copper or brass trim is ideal for decorating a bathroom in a nostalgic retro style

In addition, there are special models that are made at the request of the customer or manufacturer for non-standard bathtubs. They take into account the special sizes of containers and communications connected to them.

Reviews

Egor Vorozin, 35 years old, Minsk

The bathtub in our apartment was so old and terrible that it was scary to even look at it, and it’s not worth talking about how unpleasant it was to take water procedures. There was no longer anything to give for restoration, so we threw away the old bathtub and bought a new one, made of acrylic. At the store, the employees presented us with another unexpected task: we had to choose a drain and overflow. The small store had dozens of different models of these devices in its assortment, my eyes just ran wild. But I decided not to experiment and chose the traditional option, where the cork is tied to a chain. It is very convenient and inexpensive. Of course, modern devices have their advantages, but in my opinion, the traditional option is the most reliable.

Olga Titova, 47 years old, Orel

Previously, I didn’t even know what a drain-overflow was, but now it is one of the main elements of the interior of my bathroom. In general, my husband and I started renovations, and this also affected the bathroom. I decided to make it in an old, classic style. To do this, we bought a cast-iron bathtub, brass faucets and a massive mirror. My husband said that the drain and overflow can be installed with the old one. But the fact is that we had a plastic device and no screen. It didn't look pretty at all. Then we found a brass, semi-automatic drain and overflow on the market. And now this detail is one of the main ones in the ancient interior of our bathroom. It is also very functional.

Ivan Rogovtsev, 48 years old, Brest

Modern technologies amaze me every day. Just recently I learned that there is a semi-automatic and even automatic drain and overflow. Since this device in my house is already quite old, I decided to upgrade and bought an automatic drain option. So what can I say? This is really very convenient, and the design seems to be reliable and should withstand more than one year.

Features of device operation

To correctly install any type of harness, you must carefully study the instructions included with the kit: it contains a detailed installation diagram for the product. It is also advisable to study the properties of the material from which the system is made, as well as recommendations for operating and cleaning the structure.

The figure shows a detailed diagram of the automatic piping for an automatic type bathtub with the dimensions marked on it, as well as the method of operating the system (+)

Particularly important are the points that talk about the use of cleaning agents: some of them contain acids and alkalis that can damage metal parts, which will lead to the failure of the harness.

Installing a piping system on a bathtub

In order to mount the device, you need to purchase the device from a specialized store, as well as stock up on tools, the set of which may differ depending on the type of harness chosen.

Tools required to install the harness:

• To install a cast iron or steel siphon you will need a grinder with a cutting wheel (can be replaced with a narrow blade for metal of good strength) and a hammer.
• When installing an automatic device, you need to stock up on a small flat-head screwdriver, as well as a set of hexagons.

In addition, you need two screwdrivers (Phillips, flat), pliers, silicone sealant and cotton napkins.

Dismantling of old equipment

The work should be done in several stages:

1. The first step is to thoroughly rinse and clean the outer layer of the bathtub, and then begin dismantling the old device.
2. The outdated plastic siphon is unscrewed using pliers, and the overflow is removed with the same tool.
3. The cast iron trim is removed using a grinder, into which you need to insert a 115 mm disc. The work is done in a circle, in sectors.
4. After this, you should drive a flat-head screwdriver to pick up and remove the upper part of the old siphon adjacent to the bathtub.

The same manipulations (unscrewing or sawing) should be carried out with the overflow. Then you need to take a hammer and use it to try to loosen the siphon, and then pull it out of the sewer pipe.

Before installing a new system, you need to get rid of the old one. The most difficult thing to remove is old cast iron equipment: this can only be done with a grinder and a hammer

If you have difficulties with rusted bolts, you can use improvised means: a kitchen knife or a bottle opener. With these devices it is quite possible to cut the stainless steel and remove the lid covering the drain hole.

Dismantling the automatic system is quite simple. First of all, remove the plug and unscrew the mounting bolt with pliers or a wrench. To remove the overflow bolt, you need to unscrew the wing with a small flathead screwdriver. Having removed it, you need to unscrew the bolt and dismantle the entire structure without any problems.

Installation of a conventional bathtub trim

Assembly begins with the bottom gasket, which must be found in the kit (it is thicker than the top one). This part is coated with silicone and then put in place.

This is done in the following way: one hand slips the element under the bathtub from below, the other picks it up from above, tucking it into the hole.

First of all, you need to unpack devices purchased in stores, check their completeness, the quality of the products, and also carefully read the instructions. After this you can start assembling

The lower counter part is installed from below, while the overflow mesh with a connected bolt is inserted from above. The structure is carefully tightened with a flat screwdriver. Movements should be made clockwise.

After this, it is important to find the upper overflow in the kit and disassemble it. To facilitate the installation of this important part, a silicone layer is applied to the gasket seat, so that the part will not fall off during installation.

A thin gasket is attached along the diameter of the seat circumference, which also needs to be coated with silicone to improve moisture resistance.

After this, a small corrugated tube is taken, which is slightly stretched, and then alternately put on the nut and the conical gasket - the wide side should be adjacent to the nut.

The corrugated structure is installed in its proper place and secured with a flat-head screwdriver. In this case, you should pull it slightly with two fingers, but this should be done carefully so as not to damage the plastic part. The bolt is first held with your fingers and then tightened with a screwdriver.

If the nut falls out, you can slip a piece of a bag inside or use other methods. The edge of the thin overflow corrugation is inserted into the drain hole, after which the plastic nut is tightened.

Assembling a new water seal (siphon)

The water seal serves to eliminate odors. It is easier to assemble it separately before connecting it to the rest of the parts. One end of it is attached to the drain hole, the other - to the outlet corrugation. The corrugation, in turn, is inserted into the sewer drain hole.

Having completed the installation of the water seal, you should insert the edge of the corrugation into the sewer, and only then attach it to the siphon. Finally, it is necessary to adjust the position of the outlet and tighten all the nuts as much as possible

To check the quality of the assembly, just turn on the water and let it flow down the drain. If there are no leaks, the installation was completed correctly.

Step-by-step instructions for installing a siphon on a bathtub are given in this article.

Automatic fixture installation

Installation of the automatic siphon is carried out similarly to the procedure described above.

1. First of all, you need to open the package and find the gasket that will be installed on the drain.
2. Align it with the hole in the bathroom, so that the thinner part is at the top. If the siphon is installed on cast iron plumbing, it is advisable to cover it from the inside with plumbing sealant.
3. Unscrew the chrome-plated pressing front part from the overflow.
4. The place where the gasket fits in a circle is treated with silicone to improve the strength of the connection. In addition, the gasket mounted on the sealant will not fall or move out of place, which simplifies installation.
5. The resulting structure is pushed onto the overflow hole with one hand from the outside of the bath, while the pressing chrome part is screwed on with the other hand.
6. The next stage is the lamb, which needs to be carefully placed on the rod. After installing the element, tighten the nut with a small flat-head screwdriver. This must be done with maximum caution so as not to damage the part.
7. After this, it is important to start draining. The lower part of the structure is brought to the hole, while a drain mesh with a bolt is inserted on top, which we hold with our fingers. The connection is carefully tightened.
8. Next, you should try on the plug with the adjusting bolt. To do this, you need to insert the drain mesh into the hole of the clamping bolt and tighten it if necessary. After this, the lock nut is adjusted, which should drop to the bottom mark and then rise again.

To complete the work, a gasket and nut are inserted into the water seal part; The mating part of the drain is installed and the nut is secured. A sewer pipe or corrugation with a diameter of 40 mm is connected to the counterpart of the siphon.

Having installed the automatic piping for the bathtub, you should conduct a test run to check its reliability.

The bathtub is filled to the brim with water, which is then drained. If there is a leak, it is necessary to tighten the elements. If the leak continues, all parts will have to be disassembled and then carefully reassembled

You can also seal the problem area with silicone, but this process is not recommended for the trim that sits between the water seal and the top of the tub.

After installing the drain and overflow, connecting the plumbing to the sewer and water supply, you can build a screen for the bathroom, providing access to the piping elements.

Popular

Among the companies that offer a range of different types of plumbing products are:

• Aniplast is a well-known Russian company whose products are of good quality and affordable price;
• Alkaplast is a Czech company that produces budget siphons with automatic lifting of the drain plug;
• Hansgrohe is a well-known German brand that produces high-quality expensive plumbing fixtures, including fittings;
• Jimten is a Spanish manufacturer specializing in plastic products. The products are distinguished by excellent performance characteristics and attractive design.

In specialized stores you can find products from other companies - domestic and foreign.

Rating of TOP 11 best siphons for bathroom sinks

Page navigation:

Conclusions and useful video on the topic

The presented video shows the detailed process of assembling a plastic siphon and connecting it to the bathtub.

When choosing a bathtub fitting, it is important to take into account not only the design features of the model, but also the reputation of the manufacturer: high-quality fixtures are durable and provide a guarantee against leaks.

To prevent such troubles, it is equally important to carefully perform all stages of installation, as well as pay attention to a thorough check of the assembled structure.

Are you looking for a reliable drain and overflow system? Or do you have experience tying up a bathtub yourself? Please leave comments on the article, ask questions and participate in discussions. The contact form is located below.

Completion

I hope that my experience will be useful to the dear reader. The video in this article will help you learn more about which bathtub trim can be used in your home. I look forward to your additions and comments. Good luck, comrades!

Did you like the article? Subscribe to our Yandex.Zen channel

August 25, 2021

Bathroom, Sewage equipment, Siphon

If you want to express gratitude, add a clarification or objection, or ask the author something, add a comment or say thank you!