Choosing a heater for the bathroom. Types and capabilities of modern heating batteries

I’ll immediately answer the question: is it possible to install a heating radiator instead of a heated towel rail? The answer here is clear - yes, it is possible. Such a replacement is quite affordable and depends only on the wishes of the owner. In this situation, I consider another question more logical: “Why and how is this done?” You will get answers to this in this article.

Source art-liga.rf

Modifications of wall heaters for the bathroom

Today, a heated floor is often used to heat a bathroom. The solution is reasonable, but where to dry the robes and towels? Not on the floor. Heated towel rails and electric heaters will help solve the dilemma. The devices combine perfectly with a heated floor system - the towels dry quickly and your feet are always warm.

Water heated towel rails

This invention is not new. Every Soviet bathroom had a coil with paint peeling off from dampness. All sorts of small things like socks and handkerchiefs were dried on it. Today, the bent pipe has been replaced by an elegant chrome-plated device that performs the same functions. Such a device is powered from a hot water supply or heating system.

The coil must be made of stainless steel, because... a steel tube in a humid environment will quickly become unusable. A heated towel rail made of copper and brass can be connected to an autonomous heating system.

Electric heated towel rails

If the house does not have hot water supply and water heating, an electric heater is installed in the bathroom. It is connected to a 220 volt alternating current network and operates on the principle of an oil radiator. A coolant circulates through the tubes of the device, heated by the heating element. A standard electric battery for a bathroom is made in the form of a coil or ladder.

Electric heated towel rail in the form of a coil

Modern models consume no more energy than incandescent lamps. For convenience, the device is equipped with a timer and thermostat, with which you can set the operating schedule and temperature range.

Finally. When choosing a radiator for a bathroom, you don’t need to look at the design - the radiator can be covered with a decorative screen if necessary. Practicality, reliability, and heater power should come first. Savings are also inappropriate here. An expensive, high-quality device installed by a specialist will work for many years and will recoup its cost many times over.

Classification of heated towel rails

Dryers are divided into different groups according to type, size, installation method and material.

By type of coolant connection

The type of connection also determines three types of heated towel rails, and the type of connection plays one of the key roles when choosing a specific model.

• Water heated towel rail. Connects to the hot heating system. Heating occurs during the passage of a heated working environment. It is important to choose a model made of material that is resistant to aggressive water. During operation, there may be a risk of destruction of the structure of the internal walls, so the level of rigidity is an important factor when choosing . Made from stainless steel with a chrome finish , this is an excellent option that will last for many years.
• Electric heated towel rail. Does not depend on central heating . Requires an outlet at the installation site. Allows you to use yourself when necessary. There is a function for self-regulation of temperature data. Characterized by increased energy consumption.
• Combined heated towel rail. The most practical scheme for installation at home. You choose the connection type that is convenient for you. Alternating the heating method is optimal in different seasons of the year. So, you save money on utility bills. The cost of this modification is an order of magnitude more expensive than the above analogues.

Divided by size format

This variety is more of a design definition than an actual characteristic; it all depends, trivially, on the ratio of height and width.

• Horizontal heated towel rail. Combines the features of a dryer and radiator for heating. Installed as a window sill option. Will fit into any design. Does not take up a large area during installation.
• Vertical heated towel rail. It takes up an order of magnitude more space to be placed on the wall. Provides a large usable drying area. Available in exclusive shapes that will make your home decor stand out.

Type

There are 3 types:

1. Mermen. Powered by hot water. The advantages include durability, strength, no additional maintenance costs, and low cost. There are no maintenance requirements; replacement is required primarily not due to breakdown, but for aesthetic reasons. The disadvantage is the dependence on hot water supply or heating (to which the dryer is connected). Some devices only work in winter, when the apartment is heated. Others become cold when there is no movement of hot water through the pipes.
2. Electric ones are connected to the network for continuous operation. Their disadvantage is expensive maintenance. They are easier to install than water ones, because you don’t need to drill the walls, connect to the water supply, or use additional fittings.
3. Combined ones combine the characteristics of both types. These heated towel rails are connected to both a hot water source and an electrical outlet. The ability to change modes allows you to always maintain a comfortable room temperature.

We recommend: Hydraulic arrow for heating - purpose and main parameters

By material

Dryers are made from different materials:

1. Stainless steel will withstand high pressure. The walls of the pipe must be at least 3 mm thick.
2. Steel is a cheap material. Dryers made from it are no longer sold, but most old houses have them installed.
3. Copper is resistant to corrosion and conducts heat well. Such a product will not be heavy and looks good in appearance. Check that the pipe is galvanized on the inside for greater protection against water. The disadvantage of this option is the expensive price.
4. Brass has the same “advantages” as copper. Products made from it are cheaper. The "disadvantage" is fragility. You should only buy dryers with chrome-plated inner walls.

Other non-ferrous metals and alloys (for example bronze) can also be used. Such products are rarely used due to their high cost.

Non-ferrous metals are often used to create designer dryers of non-standard shapes and colors.

Advantages of contacting the company Warmth and comfort

1. Experience of specialists in the field of installing batteries in the bathroom. Our professionals are ready to perform installation in an apartment, country house, or other facility.
2. Individual approach. When improving heating systems, specialists always take into account the wishes of the customer. Just let us know in advance which batteries you want to use and how to install them.
3. Efficiency in solving problems. The installation of radiators will be completed as soon as possible. In the near future you will be able to start using your heating system with new high-quality batteries.
4. Availability of professional equipment. We have everything necessary for installation work.
5. Accurate execution of work. Installation of heating radiators is carried out not only quickly, but also very carefully. Certified welders and other qualified personnel comply with all established requirements.
6. Consulting support. You can always ask our specialists any questions about batteries, pipes, fittings. Managers will tell you about all the main models and components.

Contact us! We will help make your bathroom warm, cozy and comfortable! With modern, stylish batteries it will look as attractive as possible.

The bathroom should be warm - this is an axiom

In this small but extremely important room for any family, children are bathed, washed, and clothes are washed and dried. To create a comfortable microclimate in the bathroom, you need a source of dry heat

A radiator in the bathroom will not only warm you up and help dry your laundry, but will also help prevent the appearance of mold and unpleasant odors. In this case, it is desirable that the functionality of the device be combined with its aesthetic appearance.

Ballu BEC/EZER-2000

Effective combination of price and quality Country: Russia Average price: 4000 rub.
Rating (2020): 4.9 The most unpretentious device in terms of placement conditions is equipped with its own wheelbase, and therefore does not require special installation, although the wall-mounted version is structurally acceptable. It moves easily around the bathroom regardless of the type of floor covering. The moisture-proof housing of the convector is quite sealed, practically does not heat up, and does not have protruding or other traumatic elements. It is characterized by maximum stability, but in case of capsizing, as well as overheating, a shutdown is provided.

If necessary, such a device can be installed directly next to the bath and regulate the temperature. In general, according to users, this accessory is effective on an area of ​​up to 25 square meters. m. The build quality deserves attention, as does the cost of the model. The electronic type of control is complemented by a display and a timer function, which can be set for a maximum of a day. Of the useful features, the undoubted advantages are the options for blocking buttons and air ionization, which suppresses the activity of bacteria. The relative disadvantage of the heater is its weight of 4.7 kg.

Universal insertion method

The coil operates on the principle of a gravity pump. If you insert it correctly, natural circulation and proper operation of the radiator are guaranteed. It is necessary to develop an installation diagram, strictly following the model instructions, and also taking into account the location of the riser in the bathroom.

For most models, the best option for tapping is to supply the coolant through the upper outlets (and the outlet is made from below). This is achieved using universal connections for the battery in the bathroom (photos of examples of work are in our article). This type of insert has a number of advantages:

• the direction and speed of water supply in the riser do not in any way affect the performance of the battery;
• there is no need to bleed air after circulation is turned off.

Another important advantage is the independence of the installation from the location of the riser.

Polaris PCH 1096

Best-selling model Country: Russia (produced in Russia, Italy, Israel, China) Average price: 2500 rubles.
Rating (2020): 4.8 This stylish bathroom accessory attracts attention primarily with its unobtrusive, universal appearance. Ergonomic shape, almost completely closed heating element, a large number of small holes for uniform heat distribution. The product has an optimal weight of 3.5 kg and is easily moved using a wheel base or mounted on a wall.

The heater power of 1000 W is quite enough for the bathroom. The main working element of X-Shape is made of aluminum and is considered one of the most reliable, with a good service life. Using a mechanical regulator, the desired heating mode is set, there are three in total, including energy-saving. The convector is protected from overheating, moisture, and tipping over. Owners in reviews point out the silent operation of the device, ease of maintenance, and the absence of foreign odors.

Connection

Water heater

How to properly connect a water heated towel rail or radiator?

• A bypass is required before the dryer or radiator. It will ensure the passage of the riser or liner when the heater is turned off (for example, in the summer heat);
• To shut off the dryer, it is better to install ball valves rather than screw or plug valves. They do not require maintenance, always hold water tightly and have a huge resource;
• It is better to connect both the dryer and the radiator not with spurs, but with American ones. In this case, installing and dismantling the heated towel rail (for example, to lay tiles underneath) will take no more than a couple of minutes.

Electric heater

Heated towel rails, with their ridiculous power, can be connected to any outlet, regardless of grounding or wire size. But for full-fledged heaters, the instructions are somewhat more complicated:

• The outlet must be connected to ground and have appropriate terminals. The bathroom is a damp room, and a phase short circuit to the housing can lead to the most unpleasant consequences;
• The socket must have a cover that protects it from splashing water;

Wiring is calculated based on 1 mm2 copper wire cross-section for 8 amperes peak current. Let me remind you: current is equal to the result of dividing the power in watts by the supply voltage in volts. So, for a 2 kW device you need a copper wire of at least 2000/220/8 = 1.36 mm2.

Veito Blade

Modern technologies, new materials Country: Türkiye Average price: 23,000 rubles.
Rating (2020): 4.7 This brand produces unique carbon infrared models to create comfort in different types of rooms. Veito Blade is one of the flagships in its line, which provides wide functionality. The accessory is mounted using the included set of fasteners on a tripod, wall or ceiling. The positive point is that during operation, the angle of inclination can be easily adjusted, creating separate heating zones. Remote control occurs via a remote control at a distance of up to 5 meters.

The most attractive advantages for consumers are touch control based on an LED display, 4 adjustable power modes (800-2000 W), a battery is included with the remote control, and a heating area of ​​up to 25 square meters. meters. Durable carbon fiber is wear-resistant and the heating element is guaranteed for up to 5 years. The length of the power cord is about 2 meters making the device less dependent on the outlet. The best moisture protection class IP 55, the presence of a timer, overheating and fall protection are also among the positive design features.

What if you remove the radiator from the bathroom?

There is a category of citizens for whom not only the radiator in the bathroom, but even the heated towel rail is in the way and they decide to eliminate them. Immediately there is more space, neat and minimalistic, in a word – fashionable. But you can get the following results:

• temperature decrease below a comfortable level;
• increased humidity - as a result, the appearance of fungus;
• imbalance of the heating or hot water system.

This means that it is impossible to change the battery in the bathroom without employees of the service organization. They install the heat exchanger taking into account the design data of its hydraulic resistance. This is necessary for the system to be balanced. It is prohibited to even move the radiator to another place, much less completely dismantle it. We strongly do not recommend removing heating appliances from the bathroom.

Comfort “Umnitsa” TKV-2000 W

Minimum weight Country: Russia (produced in China) Average price: 2200 rub.
Rating (2020): 4.8 The fan heater is designed for wall mounting. Its flat body is made of high-quality plastic, which is resistant to temperature changes and does not deform or crack over time. The electric device is equipped with towel holders, which users call among the best design features of the model along with the weight of 1.6 kg.

But the positive aspects of bathroom equipment do not end there. It is equipped with 2 power modes - 1000 and 2000 W, which are set by simply switching the mechanical regulator. The ceramic heating element is considered the most environmentally friendly, since its operation does not lead to the combustion of oxygen. Additionally, the device has a thermostat with 3 types of airflow. The overheating protection option prevents fire and premature failure of the device.

How to hide a battery in the bathroom

How to make a radiator less noticeable? There are four ways to disguise radiators in the bathroom:

• Construction of a plasterboard box. To do this, you need to use moisture-resistant plasterboard sheets, because ordinary ones will not cope with extreme temperature conditions. The structure is constructed in the simplest way: a box is made from profiles, sheets cut to shape are placed on it. You need to make several holes in the top sheet so that warm air can escape into the room.
• Decor using tiles. This method is similar to the previous one, but differs in an increased level of energy consumption.
• Disguise behind plastic panels. This method is the simplest and relatively cheap. The low level of fire resistance is the main disadvantage of this method.
• Disguise with blinds. This method is suitable for those who value the usable space of the bathroom. Blinds allow you to have constant access to communications.

In addition to these four methods, there is also a radical one - installing the battery directly into the bathroom wall. However, due to the complexity and impossibility of servicing during an unusual situation, it is better not to tempt fate and not to commit rash acts.

Nowadays this is becoming less and less common, but some still have a cast-iron radiator in the bathroom, which was installed under the Soviets. It is clear that during repairs it is replaced with a heated towel rail, the thermal power of which is usually sufficient. In an apartment, the bathroom is small, but in cottages, for example, bathrooms are made large, so just a towel is not enough to heat it. You need to install an additional battery.

No. 10 Incorrect placement of the radiator

Equally important is the correct placement of the battery in relation to the wall. It is often placed under the windows, because it is through them that the greatest amount of heat escapes

They make mistakes when setting the depth of the device when it is either close to the wall or too far from it. The optimal distance is 2 cm.

You also need to pay attention to the height setting. If the radiator in the apartment is too close to the floor, this leads to poor heat transfer and air circulation.

You should retreat 6-10 cm from the floor. Excessively high placement of the device is also not allowed, especially with a window sill hanging over it. The consequences will be the same as with low placement. You need to leave at least 5-10 cm to the bottom line of the window sill.

The worst thing is to install heating devices inside niches and cover them with a decorative grille or screen. The air flow will decrease by 2-3 times, which will make the room noticeably colder. In order not to spoil the interior, it is better to resort to other methods of camouflage, for example, hanging curtains on the floor.

If you avoid the listed mistakes, the installation of a radiator in your apartment will go off without a hitch, and the result will delight the residents for many years.

Step-by-step installation of a battery in the bathroom

The first step is to prepare materials and tools. The tool is selected depending on the type of water supply pipes in the room. If installation is carried out through PP pipes, then it is necessary to ensure the availability of ball valves, mounting brackets, polypropylene pipes, a soldering iron and a knife for PP pipes.

The next step is dismantling the old equipment. Here you will need to do some preparatory work - if necessary, agree with the house management company on the possibility of disconnecting the riser from the water. Well, then - depending on the situation. If the coil is welded to the riser, you just need to cut it off with a grinder; if it is screwed on, unscrew it and dismantle it.

Step three. We install bypass and ball valves. Of course, the battery mount can be installed without a bypass, but following the recommendations of experts, it is better to install it. Ball valves must be installed at the ends of the dryer. This will allow you to shut off the water without turning off the riser.

The final step is installing the dryer coil. The process here is the same as with nailing a shelf to the wall. The only condition is to align the coil vertically and maintain the permissible distance from the wall.

Timberk TCH AR7 1000

Best cost of infrared heater Country: Sweden (manufactured in China) Average price: 1,700 rubles.
Rating (2020): 4.5 The IR type model is in consumer demand, since the low cost does not in any way affect the quality of the product. The product is only limited in functionality, and those that are present do not cause any complaints. The thermal heating element is safe to use and quickly generates heat over an area of ​​up to 10 square meters. m. In general, the device is a great space saver, because it can be placed on a wall or ceiling.

Mechanical control does not create any difficulties. The owners of the accessory cite the lack of a thermostat as a significant disadvantage. At the same time, engineers have provided for an emergency shutdown in case of overheating. The advantages also include the low noise operation of the device, compactness, and absence of unpleasant odors. The fine-mesh metal grid of the housing prevents foreign objects from getting inside.

Arguments and counter-arguments

Behind

• According to current SNiP, the temperature in the bathroom must be maintained at least +25C all year round. In the cold season, it is quite difficult to provide it without its own heat source in the room;
• In the limited space of a city apartment, the bathroom is often used for drying clothes. Where do you think it will dry faster - in a cold room or in a warm one?

The causes of fungus are cold and dampness.

Against

• In a cramped bathroom space, a radiator heated to 70 - 90 degrees often causes burns;
• In the summer heat, heating an already stuffy room becomes inappropriate.

Heliosa EH110/FM

The best efficiency of the device Country: Italy Average price: 10,000 rubles.
Rating (2020): 4.9 The development belongs to the type of infrared (IR) heating devices and can be installed both in bathrooms or bathhouses, and in open areas. The device has a classic design for this type and is light in weight (2 kg). Its most important advantage is its high water protection class IP23.

Another important feature is cost-effectiveness. The device can be used for zonal heating of a room area, in particular, a bath sector or a place for drying clothes. In addition, heated objects retain heat for a long time, gradually saturating the air with it. The presence of a special stainless steel grill in the design protects against burns. Among the advantages of the model, owners highlight the durability of the lamps, a durable steel case that protects them from mechanical stress. The only disadvantage of the IR device is its high cost, but its performance and long service life make it popular among consumers.

Which battery to choose

When choosing a heating battery for a bathroom, you should take into account the fact that not every one of them can operate reliably and for a long time in conditions of high humidity.

To choose the right radiator, you need to take into account all the features of its operation.

Let's consider the main advantages of modern batteries.

Cast iron. Such products often look quite bulky, but are characterized by optimal heat dissipation and a long service life.

When choosing a battery, pay attention to the presence of a special protective coating (powder coating). Models with it are maximally resistant to corrosion and constant exposure not only to moisture, but also to steam, temperature changes, and aggressive detergents. Steel

Such products are not suitable for use in the bathroom. This is due to the fact that steel models rust quickly. The only exceptions are modern models made of steel with anti-corrosion coating. But often such radiators are quite expensive. Aluminum. Such models are compact and lightweight. They are ideal for bathrooms in private houses and cottages. Autonomous heating systems are not subject to hydraulic shocks. Thanks to this, you don’t have to worry about the battery simply breaking during one of them. Bimetallic. Such radiators in the bathroom can last up to 15-20 years. Bimetallic models cope excellently with all their functions. Original products also decorate the interior of the bathroom. They can be used as heated towel rails, robe hangers, mirror stands, etc.

Choosing a water heated towel rail

Choosing the right heated towel rail is a whole science, and especially a water one. The most important thing here is the shape, size and even the location of the bends, and there are also technical characteristics that also need to be taken into account.

Modern heated towel rail

Specifications

The operating pressure in the DHW system should be in the range from 0.3 atm to 6 atm. The pressure in the centralized heating system greatly depends on the area, but is rarely higher than 10–12 atm (in high-rise buildings). Select water dryers according to these parameters.

Before choosing a heated towel rail, pay attention to such an indicator as the maximum temperature. For hot water supply, this figure is rarely higher than 60 °C; for heating, few people give 80 °C. From this point of view, all stainless steel dryers are suitable, they have a maximum temperature of about 105–110 °C. Nevertheless, emergency situations occur when water is supplied heated to a hundred degrees or even higher, so this reserve will not hurt.

Deciding on the form

Water towel dryers come in different shapes. They can be divided into several groups:

• U or U shaped. The simplest in form and having the lowest cost. The disadvantages include their small “usable” area, as well as the not very large amount of heat that they can generate. You can't hang a lot of things on them. But such a towel dryer in the bathroom, with the correct size selection, can “stand” in the place of an old similar shape without modification.
• Snake, coil or M-shaped. A slightly more complex shape, more usable area and heat generated. They are also not very difficult to connect and have a low price. Snake dryer. Maybe not a masterpiece, but it lasts a long time

• Ladder. A heated towel rail consisting of a number of horizontal bars united at the edges by vertical collectors. The crossbars can be straight or in the form of a snake. Such a device usually has two connection methods - side and bottom. A more complex form requires a well-chosen scheme, otherwise it will not work. In addition, due to the high material consumption, the cost of such dryers is several times higher than coils.
• Non-standard complex shapes. There are unusual towel rails that look more like designer decorations than plumbing fixtures. Their prices are not low, and most of them are delivered “to order”. Problems often arise with their connection, so you need to choose the right circuit and consult a specialist.

Choosing a bathroom dryer according to its shape is both simple and difficult. You need to consider how and where you can install the design you like. At the same time, do not forget that you will have to connect it to a riser, which means pulling pipes along the walls to it. Moreover, most likely, the gasket will be hidden, that is, it will be hidden in the wall, which means that it will be necessary to ditch them or install a false wall.

Connection and installation features

An electric heated towel rail is connected to a regular socket, but since the installation location is a bathroom with high humidity, the voltage must be supplied through an RCD that breaks phase and zero; an automatic circuit breaker is also needed, perhaps one contact. The choice of their electrical parameters depends on what other devices will be connected to this line. It is not worth running a separate line to the heater due to its low power.

Thermostats have different shapes, but the functionality is usually the same

The heated towel rail can be installed anywhere. Usually the protection class allows it to be installed even above a bathtub (II), but this is hardly worth doing. It’s inconvenient, and things will get wet. It is usually best to install an electric dryer on any free wall. Often so that you can reach from the bathtub or shower stall. If the bathroom is combined, you will have to choose. You can also place it not far from the bidet or toilet with a hygienic shower. By the way, mounting brackets are usually included in the kit, so you don’t have to invent anything.

How to choose a battery for the bathroom

It is extremely difficult to remove the fungus.

There is no dispute about tastes, so everyone chooses the design of a heated towel rail or radiator for the bathroom for themselves

The first important decision is what the heat output of the heating device should be. If according to the rules, then you need to calculate heat loss

You need to be able to do this, as there are a lot of nuances. It is unlikely that you will be able to make a competent calculation at a glance. To get an accurate value, you need to contact professionals.

The popular method is to select a battery for the bathroom according to the area of ​​the room. Yes, the resulting value will be approximate, but the calculation is not complicated, and most importantly, it works. For every meter you need 100 W of thermal energy (ceilings 2.5 m).

Having found out the required power, decide on the type of heating device:

Naturally, water heating registers include heating registers (battery and water towel). Their advantage is that there are no operating costs. The same cannot be said about electric heated towel rails, but they also have their strengths. This is work all year round without interruptions, a varied design, the ability to control the device remotely via smart sockets

Pay attention to the connections for connecting water towels to the circuit. They can be located on the side or bottom

The distance between them must coincide with the pipes on the risers.

How to adapt a fireplace for heating a dacha is written here.

AEG WKL 753 S

Model with automatic climate control Country: Sweden Average price: 6200 rub.
Rating (2020): 4.6 The convector-type device features an optimal power of 750 W for the bathroom, a moisture-proof housing, looks aesthetically pleasing, and the device is safe for health. A significant advantage of the design is that it is equipped with a remote control and the possibility of automatic climate control. The operation of the device is based on mechanical control, which even a beginner in operating such equipment will quickly master.

In reviews, the owners of the model indicate the presence of a thermostat, which helps create a comfortable microclimate near the bathtub. A special fuse protects the device from overheating and the consequences of power surges. Among the disadvantages are the lack of a timer, the weight is 4.2 kg, so it is recommended to mount the accessory on the wall not above your head. In general, the build quality of the product and equipment correspond to its price.

Heating appliances in the bathroom

The heated towel rail performs the function of heating the bathroom.

There is no doubt that a battery is needed in the bathroom, but why is it there? We are talking about an ordinary radiator that is in every room. In the bathroom, the heated towel rail is mainly used as a heating device. This is, in fact, a water heating register, whose main function is heating. This means that he is also a kind of battery.

The bathroom is small, so a towel is usually enough. In large bathrooms, the power of a heated towel rail will not be enough; in this case, it is necessary to install a battery in the bathroom. Suitable for this:

The latter are the most practical and reliable. But it also happens that you inherited a cast-iron radiator in the bathroom along with the apartment. Previously, they weren’t particularly worried about making it beautiful. The main thing is quality and durability, so we installed ordinary cast iron radiators in three sections in the bathroom. Usually they are replaced with either a water heated towel rail or a combined unit (battery + heated towel rail). Here you need to look at the heat loss of the room.

Read more about the heating device in the country in this article.

Practical advice from professionals

Example of an electric and infrared heater

1. How to cover the radiator in the bathroom? Special plastic screens are sold for this purpose. You can also “sew up” the radiator with plasterboard or hide the radiator under the bathtub, if space allows.
2. Installing and replacing the battery in the bathroom is quite simple. If this concerns electric drying, then you need to mark the place for the brackets, connect the socket and hang the structure on the wall. You can also connect the dryer to the “warm floor” system. If this is a water dryer with a battery for the bathroom, it is better to turn to professionals, since incorrect connection threatens to create an air lock in the entire water supply system.
3. If you need a battery under the bathtub, it is best to take a medium-section pipe and run it along the lower level of the baseboard (you can run it around the perimeter). But it is extremely important to avoid sharp corner transitions, since the passage of water flow in them may slow down.

Advice! New designs are often complemented by accessories. There are batteries in the bathroom with shelves, stands or hooks. This allows you to use the entire usable area and facilitates drying options.

When choosing an electric convector for the bathroom, a simple heated towel rail or an oil radiator, do not look at beauty, because the design can always be decorated. But practicality, durability, service life and power should come first. And, of course, the price of the device.

General installation requirements

Installation of a water-based battery is carried out in compliance with the basic requirements:

• The diameter of the dryer tubes should be equal to the diameter of the riser - no narrowing or expansion.
• It is necessary to install a jumper between the heated towel rail outlets.
• Shut-off valves must not be installed on the lintel. This also applies to the section of the pipeline up to the bypass.
• The dryer must be installed at a height of at least 120 centimeters from the floor.
• The distance between the wall and a heated towel rail with a tube diameter of up to 2.5 centimeters should be 3-4 centimeters. With a diameter of more than 2.5 - 6-7 centimeters.

Warranty, prices

Prices for radiators depend on their size and power, the material from which they are made, and the finish. A regular one costs from 4,900 rubles, an electric one - from 3,700 rubles.

You will pay about 3,300 rubles for a separate electric radiator. Warranties for electric dryers and heaters range from one to 2 years, although longer periods of up to 8 years are available.

REDMOND SkyHeat 7002S

Convenient control via smartphone Country: Russia Average price: 5800 rub.
Rating (2020): 5.0 Users liked this convector because it is perfectly adapted for installation both in the bathroom and in other rooms. This rather compact device received from the developers a reliable waterproof housing that is not afraid of drops of water or steam. The narrow device is easy to hide in small niches, and installation does not take much time. As for functionality, the owners note the useful power, thanks to which the area is about 20 square meters. m is filled with warmth in just half an hour. The built-in regulator allows you to control the heat distribution. When overheating occurs, automatic shutdown occurs.

The advantages also include electronic control via Bluetooth. Despite the lack of Wi-Fi support, owners note the simplicity and speed of the application and the ease of working with settings. If noise level is important to you, then this heater will not disappoint, as it operates very quietly.