Selection and rating of pneumatic, electric nail guns

The modern tool is designed to remove the high workload from a person, and at the same time increase the specialist’s performance several times. In the case of a nail gun, this efficiency indicator is without a doubt one of the highest. Installation of profiles for plasterboard systems, soft roofing, furniture manufacturing and other types of work with this device are more intensive and require less energy.

The review involves different types of tools for driving nails, pins or special staples. The best models of pneumatic, electric or gas pistols are presented in their respective categories. The rating position of the models is based on the characteristics of the equipment, its operating parameters and the opinions of specialists who use nailing units in their work.

Rating of gas nailers

Gas guns can be used both in finishing and in construction. A comparison of nailers shows that, depending on the specific model, they can demonstrate good power.

SPIT Pulsa 800P+

The French-made functional nailer is equipped with a gas cylinder designed for 600 shots, while the operating speed of the device is two blows per second. The nailer's magazine is small, with only 20 elements, but if desired, it can be replaced with a more spacious one. The maximum length of fasteners is 40 mm.

Attention! The nailer supports the Start & Go energy saving function and turns off automatically after a minute of inactivity.

You can buy a SPIT nail gun from 82,000 rubles

Toua GSN F1

The gas nailer is suitable for working on steel and concrete surfaces. The cylinder capacity is enough for 1400 shots, the pistol is equipped with two barrels - for shallow depth and for maximum power strikes. Capable of operating, including in the open air at sub-zero temperatures. The system is powered by two high-capacity batteries; a charge indicator is provided on the handle of the nailer.

You can buy a Toua nail gun from 27,000 rubles

Lixie LXJG-III

A professional-type gas gun can work without drilling with any materials - concrete, steel, brickwork. Maintains good speed, drives nails of medium length up to 32 mm into the surface. It operates in conjunction with a powerful battery, the capacity of which is enough for 1250 shots.

Attention! The nailer has an extended package; it comes with two batteries, a charger, a storage case, safety glasses and earplugs.

You can buy a Lixie nail gun from 40,000 rubles

Rating of the best models of electric nail guns

Nailers operating from a socket have low power. Most often they are used for interior cladding.

PIT PST6001-C

An inexpensive electric nailer delivers 20 strokes per minute cycle. The maximum length of nails for such a gun is 32 mm; the device can drive fasteners not completely, but to a certain depth. Users consider the 100-element magazine to be a plus; during operation, you don’t have to replenish the drum too often.

You can buy a PIT nailer from 3,000 rubles

Stanley Hand Tools 6-TRE650

The productive finishing gun is capable of working with nails of various lengths from 15 to 32 mm. You can replace pins in the device’s capacious magazine through a special window to save time; control is carried out by pressing the trigger, and the force of impact can be adjusted. The nailer's cord length is 2.5 m, which is usually sufficient for home projects, but an extension cord may be required for larger areas.

You can buy a Stanley nail gun from 6,600 rubles

Bison ZSP-2000

The repair and construction gun produces 20 blows per minute and supports power adjustment. Compatible with short-length staples and pins for mounting sheathing; the model provides protection against accidental pressing or activation due to loose contact with the surface.

You can buy a BISON nailer from 3,600 rubles

Rating of the best battery nailers

Battery-powered nail guns are not very powerful and are not usually used for construction. But they are in demand for internal and external cladding.

Ryobi R18N18G-0

The rapid-fire cordless nailer with light works with nails up to 50 mm. Performs up to 60 strikes per minute, equipped with a spacious magazine for 105 fasteners. Among the useful functions, one can note the adjustment of the force of the shot; with the help of a nailer, you can not drive nails in completely. The downside of the device is the lack of a battery included; you will have to buy it separately.

You can buy a battery-powered nailer from Ryobi from 14,000 rubles

DeWalt DCN 692P2

This reliable nail gun from the professional category is distinguished by its increased power. Despite its battery-powered system, it is capable of firing pins up to 90mm in single or high-speed mode. Supports adjustment of power and impact force, produces little noise and almost does not vibrate during operation. Supplied in a case and with two batteries.

The average price of a DeWalt DCN nailer is 46,000 rubles

Makita DPT 353RFE

The Japanese-made finishing nailer can work with fasteners up to 35 mm. The device’s magazine holds 130 elements, so using a nailer you can quickly process large areas of the surface. In poor lighting, it is possible to use the backlight. Among the advantages is a system for protecting batteries from complete discharge or overload.

The average cost of a Makita DPT nailer is about 30,000 rubles

Rating of powder pistols

Powder-type nailers are slower than pneumatic and gas nailers, but do a good job of driving nails into hard material. Models from well-known brands are completely safe to use.

Walte PT 950A

Multi-shot nailer for wood, metal, concrete and brick supports fastener lengths up to 80mm. Works with red and black cartridges, the model provides adjustment of impact power and a wear protection system for the piston and shock absorber. The nailer is reliable and has a long service life.

You can buy a Walte nailer from 17,000 rubles

Toua 307

The gun is designed for driving 15-76 mm nails into brick and concrete; the impact energy when fired is 100-450 J. Among the features, one can note a rubber attachment on the barrel, which prevents the scattering of concrete fragments when shooting. The nailer comes with two hex keys, a plastic case and a cleaning rod for cleaning the tool.

The price of the Toua nail gun is only about 4,500 rubles

Spit P45

The single-shot nailer for concrete and metal is lightweight and compact with a good impact force of 320 J. Most often, the device is used for fastening cellular film and waterproofing; the model works with green, red, yellow and brown cartridges.

You can buy Spit P45 for an average of 42,000 rubles

Rating of the best pneumatic nail guns for 50-90 mm

The greatest demand is for nailers that support nail lengths up to 90 mm. They are usually used in frame construction, but the models are also suitable for indoor work.

Sumake R-90PA

The contact action nailer is equipped with a magazine for 300 fasteners 50-90 mm. Optimally suitable for construction and finishing, works in tandem with a compressor with a nominal pressure of at least 7 bar. In the model, you can adjust the depth of driving fasteners.

The average price of a Sumake nailer is 31,000 rubles

FoxWeld Aero 6524

The pneumatic type nailer is capable of working with 8 bar compressors. It efficiently hammers nails up to 90 mm into wood; if desired, the user can adjust the impact force and the depth of immersion of the fasteners. The magazine of the pistol is cassette type, medium capacity, with 80 elements.

You can buy a FoxWeld Aero nailer from 11,000 rubles

Fubag N90

A pneumatic gun with an air flow of 120 liters per minute quickly and efficiently hammers 50-90 mm nails into the surface. Works with compressors capable of providing an outlet pressure of 4-7.5 bar, especially convenient when performing work at an angle. The nailer is quite heavy, but the ergonomic handle allows you to hold it with one hand for a short time.

You can buy a Fubag N90 nail gun from 6,900 rubles

Choosing a compressor for a nailer

To operate, a pneumatic nailer requires a compressor, and this device must be purchased separately. When purchasing a nail gun, it is recommended that you carefully study its instructions and find out if the tool has specific requirements for the air blower.

It is better to choose a compact compressor for a nailer so as not to weigh down the structure.

Most often, nailers work with compressors up to 8 bar. Such units provide sufficient performance, but at the same time they cost quite moderately and do not look very bulky.

Top 10 best nailers for frame houses

In frame construction, nail guns are used for long fasteners of 50 mm or more. There are many corresponding models on the market, mainly pneumatic and gas devices.

Toua GFN3490 CH Li

The gun for long slatted nails operates using a battery, and the impact energy is provided by flammable liquefied gas. The nailer is designed for working with wood, plywood and fiberboards and demonstrates good resistance to negative temperatures. On one battery charge it can fill up to 4000 elements.

The average price of a Toua nail gun is 28,000 rubles

Fubag N70C

The pneumatic nailer for 45-70 mm nails is suitable for framing work. It has a drum-type magazine for 300 fasteners and is capable of operating at an inclination of 15 degrees. The hammering force can be adjusted; the nailer operates by contact.

You can buy Fubag N70C from 14,000 rubles

DeWalt DCN890N

The rapid-fire cordless gun with a brushless motor works with nails of an average length of 57 mm. Produces 240 strikes per minute, the magazine holds only 33 fasteners. The triggering power can be adjusted, and there is illumination for the work area.

You can buy a nailer DCN890N from 39,000 rubles

AEG B18N18-0

The wear-resistant pistol supports single and rapid-fire modes, works with elements up to 55 mm in length. Designed exclusively for driving nails into wood. There is LED lighting and convenient access to the store; the kit includes a storage case.

You can buy an AEG nail gun from 28,000 rubles

DeWalt DCN660N

The medium-power cordless nailer is capable of driving 32-63 mm fasteners into wood. It has a good magazine with 110 elements and adjustable impact force; it can perform 240 strikes per minute.

You can buy a nailer DCN660N from 31,000 rubles

Fox Weld Aero 6522

The pneumatic contact nailer for 40-90mm nails holds 300 fasteners in a drum magazine and can operate at a 15 degree angle. It operates with an 8 bar compressor and can drive elements both completely and with incomplete immersion into the wood.

You can buy a frame pistol Fox Weld Aero from 24,000 rubles

Fubag N65C

Another model from a popular brand works on a pneumatic principle with a 7 bar compressor. The maximum length of fasteners is 55 mm. In this case, 400 elements are placed in the drum. The gun shows very good performance, although its use in frame construction is limited due to the average length of the nail.

You can buy a Fubag nailer from 13,000 rubles

AF-0034

Powerful nailer for 100 mm slatted nails works with smooth, rough, galvanized types of fasteners. Suitable for driving elements at an angle, balanced to be held in one hand. The nose of the device is equipped with spikes that prevent the nozzle from slipping off an inclined or wet surface.

You can buy a nailing tool AF-0034 from 26,000 rubles

Caliber PGSZ-18

The pneumatic nailer is designed to work with 50 mm fasteners. It copes well with repair and construction tasks, fires almost no blank shots and rarely bites nails and staples. It has a budget price and at the same time shows good quality of impacts. The only downside is the lack of additional options and settings, but for the price the nailer is very good.

The average cost of a Caliber nail gun is only about 2,400 rubles

Hitachi NT 65A2

The rapid-fire air gun fires 180 times in a minute and holds 150 nails in its magazine. The length of the fastening element is a maximum of 65 mm.

The cost of a Hitachi NT nail gun is about 12,000 rubles

Purpose and types of construction staplers

A simple and convenient construction device, which has universal connecting elements - staples, is an analogue of a conventional office stapler. But the power and productivity of the stapler allows you to solve far from office tasks. Construction staplers or, as they are also called, nail guns are used in the following cases:

• reupholstering furniture or upholstering any item with textiles;
• installation of plastic panels;
• installation of thin-layer insulation;
• fastening carpet/coverings to the floor;
• some types of facing work;
• fixation of low-current electrical and computer circuits, cables, wiring;
• assembling the back wall of furniture;
• covering frames with sheets of plywood and other materials;
• fastening of film, posters.

Each of these cases has its own specifics of operation and involves the use of certain types of construction staplers.

What types of tools are in question, and where they are best used, we will find out further.

1. Mechanical or manual stapler.

The most common type of stapler. The principle of operation is similar to the clerical one: bringing the mechanism into action using one’s own strength. The device is compact and lightweight, it is convenient to use in extreme positions and hard-to-reach places for fastening cardboard, film and similar materials, upholstering furniture, installing insulation and insulation. Disadvantage of this type of tool: it is difficult to use for a long time.

1. Electric staplers.

For a larger volume of work, a network device is used. It is more powerful than a manual one and is capable of joining hard materials and woods. Impact force can be adjusted for different surfaces. Disadvantages include high cost, weight and availability of electricity.

1. Battery analog.

Battery models do not cause inconvenience due to the built-in cord, like electrical appliances. They have high performance and work autonomously. Disadvantages include weight, cost and the need for periodic charging.

1. Pneumatic stapler.

These types of construction tools are most often used in carpentry and furniture production. Has the greatest productivity using the power of compressed air. Disadvantage: it must be connected to an expensive compressor.

Instructions: how to use a construction stapler

The advantages of the device are safety, time saving, versatility and the ability to mount in hard-to-reach places. To know how to work with a tool correctly, you need to understand the structure, type of equipment and how to insert staples.

Fastening is carried out using staples, pins or special nails. According to the operating instructions, it is necessary to use suitable fasteners and adjust the impact mechanism for the specific material. To fix the connecting element, you need to press the stapler tightly to the place where it is needed. Without lifting the tool, press the trigger lever.

Mechanical staplers have a screw. If you twist it harder, the impact force will increase, and the ejected staple will go deeper into the surface. You need to reconfigure it every time you start working with a different material. After adjustment, it is recommended to check the first blow on an unnecessary workpiece: the fasteners should fit the entire length of the legs.

Locking the trigger mechanism is required when refilling the magazine. It’s easy to learn how to charge a staple gun: move the pressing spring, like in a stationery stapler, and place the staples in a special groove, return the spring to its place. The tool is ready for use.

Choosing the right construction stapler

The device in question can be used both in large-scale production and at home. Moreover, for the home and garage it is better to buy a model of a mechanical or electrical type when frequent and long-term work is planned. In other cases, there is no point in overpaying for the tool. If the strength and energy source of the driving blow are important, then a pneumatic nail gun will do the job best. A stapler that operates on mains power can create inconvenience in small spaces due to the interfering wire. The battery does not have this drawback, but can run out at any time. Moreover, power consumption is affected not only by the duration, but also by the complexity of the work. A review of the best nail guns and staplers will show you what to look for when purchasing a tool.

How to choose a nailer

Before purchasing a nail gun, you need to determine for what purpose it is needed. When constructing buildings and finishing, tools with different designs and performance characteristics are used.

How to choose a pneumatic nailer

Pneumatic nailers are the most powerful and are usually used in construction. When choosing such a tool, you need to pay attention to several points:

1. Drum capacity. A magazine with 80-100 rounds is considered optimal. With smaller values, the drum will have to be replenished all the time; with larger values, the instrument will become too heavy and inconvenient to use.
2. Adjustment of driving depth. In some cases, the nails should not be immersed in the base all the way to the head.
3. Safety system. Built-in protection against accidental activation and repeated shots prevents injuries during installation work.

Also, when purchasing a pneumatic nailer, you need to study the requirements for the compressor in advance and find out the air consumption for one blow. The performance of the nail gun and its operating speed will depend on this indicator.

Which nailer to choose for building a frame house

In frame construction, pneumatic or gas guns are usually used that can pierce dense boards. This type of nailer should work with nails of at least 50-90 mm with O-shaped or D-shaped heads. Even better, if the device supports a mounting element length of up to 220 mm, this expands its range of applications.

Which nailer to choose to imitate timber

Imitation timber is a facing material in the form of wooden panels with a thickness of about no more than 3.6 cm. To drive pins into such boards, it is customary to use sheathing guns that support a nail length of 25-75 mm with a head width of up to 7.5 mm.

Important! Sheathing the frame involves a fairly large consumption of fastening material. Therefore, it is better to buy a nailer with a spacious drum.

Choosing a nailer for lining

Lining is a fairly thin wooden material used for interior cladding. As a rule, powerful nail guns are not used for its installation; in this case, the capabilities of the so-called “staplers” are sufficient. Nailers of this type work with 6-10 mm nails, as well as with studs without heads, allowing for an inconspicuous attachment point.