general characteristics
The Aquaphor OSMO-50 filter (version 5) is a reverse osmosis system designed for deep purification of water from salts, additional purification from colloidal and mechanical particles, as well as organics, viruses and bacteria. Extraneous odors and unpleasant taste are removed from the liquid. The system can be used to purify water from a well or municipal water supply.
During operation of the device, liquid passes through a semi-permeable membrane. In this case, pressure is applied from the water side.
The presented device comes in two modifications. The first of them works under the pressure that exists in the water supply network. If it is low (does not exceed 2 atm), you need to purchase a second modification. This is “Aquaphor OSMO-50” (version 5) PN. It comes complete with a pump that increases the pressure in the system.
Both varieties have high cleaning quality. These are ultrafine filtration devices. This result can be achieved thanks to the presence of a membrane and pre-filters. The system removes all harmful impurities from the liquid. Only water molecules can pass through the membrane. All chemical elements that are larger in size remain on the other side of this barrier. The result is crystal clear water.
Chlorine, oil products, nitrites and nitrates, organic matter and mechanical pollutants are removed from the liquid entering the system. In addition, the water is softened, as hardness salts are removed from it. Therefore, it can be used for cooking; scale will not appear on the walls. This is especially important for some types of kitchen appliances, such as coffee makers.
Structural elements
Let's look at the performance and role of each:
- Polypropylene cartridge – consists of 100% polymer, helps remove mechanical impurities. It lasts a long time, as it resists bacteria and chemicals, and its fibers on the inside are even stronger than on the outside.
- Carbon filter – with granular loading, responsible for eliminating organic matter and chloride compounds. It is a mandatory functional part of any equipment.
- STO-catcher - helps to trap even particles of contaminants 5 microns in size and larger (including harmful bacteria). It is a pressed block with a retaining shell made of polypropylene, which helps remove the coarsest fractions. It is made quite rigid - due to the built-in core.
- The membrane is a semi-permeable structure with the most dense mesh, allowing only O2 and H2O molecules to pass through. Since it is very sensitive and easily clogged, all the previously described elements are located in front of it to prevent it from clogging. All impurities that it stops must be washed off.
- Post-catchers have a service life of up to 5-6,000 liters, so they are replaced relatively often. They are placed after the main cleaning element, hence the name. They are used until the liquid is finally ready for consumption for food purposes.
MBFT-75 Membrane for 75GPD
SF-mix Clack up to 0.8 m3/h
SF-mix Runxin up to 0.8 m3/h
Specifications
The package includes several required components. One of them is a storage tank. The fact is that the system cannot filter the liquid quickly. To meet the users' need for clean water, a tank is installed in the system. It has a volume of 12 liters in the model “Aquaphor OSMO-50 A” (version 5.) 10 liters is its usable volume. It is made of metal.
The system is designed for installation under the sink. Filters have an open housing. The system is designed to filter liquid in a cold water supply. The liquid temperature should be 4-38°C. The working pressure in the water supply should be 2.8-6 atm.
In the water purifier “Aquaphor OSMO-50” (version 5), the liquid goes through 5 stages. Purified water is supplied from a tap, which is supplied in the kit. It has a classic design.
An important indicator of any reverse osmosis filter is its performance. The presented model can clean up to 190 l/day. If this is not enough for your family, it is recommended to purchase another system. For example, it could be “Aquaphor OSMO Crystal 50” (version 5). It is capable of filtering 375 liters of water per day. This is enough not only for a large family, but also for a medium-sized office team.
The advantage is the use of universal flasks in the design. This makes it easy to select the right cartridges and replace them. To do this, you do not need to call a service representative.
What elements does the kit consist of?
In general, a do-it-yourself reverse osmosis system is relatively easy to assemble, including because it comes immediately with all the necessary functional components - and this is:
- a membrane that acts as the main barrier;
- a block with preliminary catchers - a pair of mechanical ones and one cartridge;
- mineralizer with restorative function;
- two keys - to facilitate the replacement and tightening of fasteners;
- faucet with panel - for adjusting the pressure of drinking liquid;
- tees-connectors, flexible hoses and other connectors.
When choosing a specific model, you should always pay attention not only to the completeness of the package, but also to the compatibility of individual components, as well as to the performance of the equipment as a whole.
Features of operation
The delivery set of “Aquaphor OSMO-50” (version 5) includes several required elements. To perform installation correctly, you need to consider the main components and their features. Thus, the Filter has three pre-filters. Water passes through them before reaching the membrane. This allows you to remove coarse impurities from the water and increase the service life of the membrane.
The first pre-filter is a polypropylene module for coarse cleaning from mechanical impurities. Its service life is 3 months.
The second cartridge “Aquaphor OSMO-50” (version 5) is a deep cleaning module. It has been in use for 6 months. This is followed by a polypropylene cartridge for mechanical purification. It needs to be changed every 3 months.
The water then hits the membrane. This is the stage of deep purification. The membrane must be replaced every 1.5-2 years. The fifth stage that water goes through is conditioning; for this, the system has a 2 in 1 module that corrects taste and smell. It is changed once a year.
Hydraulic and technological diagram of reverse osmosis assembly
They look like this:
Attention, in the second case, a timer is responsible for regeneration: at the right moment it allows topping up for a while, and when the H2O level in the tank reaches a certain point, it also gives a signal about the end of the intake.
Customer Reviews
Considering reviews of “Aquaphor OSMO-50” (version 5), it should be noted that buyers leave mostly positive reviews about the presented model. If you have experience with this reverse osmosis system, please share it in the comments to the article.
Buyers note that the quality of the output water is high. Even in areas with very contaminated liquid, it is possible to get rid of almost all impurities. This has a positive effect on people’s health and the operation of household appliances.
The advantage of the model is the presence of a mineralizer and an additional post-cleaning carbon filter. The water has no foreign odors. The mineralizer restores the normal taste of the liquid. The point is that after passing through the membrane? water loses almost all the minerals that our body needs. Users note that the mineralizer that comes with the kit eliminates this drawback. The water has a pleasant taste, since its composition is as close as possible to natural.
Among the negative reviews about Aquaphor OSMO-50 (version 5), it is worth noting the slow filtration process. However, for a family of 2-3 people, the presented purifier is ideal. If there are more than 4 people living in a house, it is worth purchasing a more productive system.
Also, some buyers do not like the design of the faucet that comes with the kit. If necessary, it can be replaced by purchasing a suitable model from the appropriate store.
In general, buyers agree that the presented filter is distinguished by high quality water purification. It is easy to operate. There are no difficulties when installing or replacing cartridges. If they are replaced in a timely manner, the water quality will remain consistently high. The system can even cope with complex contaminants, such as hydrogen sulfide, nitrates, viruses and bacteria. Therefore, you can drink water, cook food with it and give it to children.
Expert reviews
Considering the reviews of “Aquaphor OSMO-50” (version 5), which are left by experts, specialists in the field of cleaning equipment, it can be noted that they call the model high-quality. This filter has more advantages than disadvantages. Therefore, it is in great demand.
Among the main advantages, experts cite the versatility of the flasks and low cost. However, these are not all the positive qualities of Aquaphor OSMO-50 (version 5). The presented model includes universal flasks, which greatly simplifies the system maintenance procedure. Also, such a solution by the purifier developers made it possible to reduce operating costs.
Experts note that the advantage of the model is high-quality cleaning of chlorine contaminants from liquids. For this purpose, the system has two carbon cartridges. This also helps eliminate all foreign odors.
A positive quality of the filter is the disinfection of liquids with silver ions. Also, a unique technology that is used in the presented model is the Aqualen loading. It enhances the effectiveness of carbon cartridges.
Another undoubted advantage is its small dimensions. Installation is not difficult, since finding a place for installation is not difficult.
Among the disadvantages, experts cite the lack of transparent flasks. This does not allow you to control the level of contamination of mechanical cleaning cartridges.
System installation
Before starting operation, you need to study the instructions for “Aquaphor OSMO-50” (version 5). If the installation process is performed incorrectly, this may result in system failure. In this case, warranty service will not be provided.
To install the filter yourself, you need to turn off the water in the system. The kitchen faucet needs to be opened to release the pressure. The connection point is cut into the water supply. The external thread must be wrapped with FUM tape.
Next you need to connect the JG tube. You need to pull out the retainer from under the plastic sleeve. The end of the tube must be moistened with water, and then inserted into the fitting to a depth of 2 cm. It should rest against the wall. The latch must be installed in place.
Next, you need to proceed to installing a faucet from which you can draw clean water. You need to make a hole in the sink with a diameter of 1.2 cm. A seal is put on the tap thread, and then a washer and another seal. The tap is inserted into the prepared hole. On the back of the sink, a plastic washer, a lock washer and a metal nut are placed on the threads.
The instructions for “Aquaphor OSMO-50” (version 5) say that all actions must be performed in a certain sequence. You need to put the nut on the plastic outlet. The conical sleeve must be inserted into the tube. The nut is screwed onto the valve bushing.
A drain clamp is installed in front of the siphon. For it you need to drill a hole with a diameter of 7 mm. You need to glue a gasket on the inside of the clamp (the protective film is first removed from it). The holes in the fitting and the drain line must be aligned. Then the bolts are tightened. They should be fixed evenly. In this case, both parts of the clamp will be parallel.
How to choose a suitable design
When choosing an Aquaphor filter, you must take into account the quality of the incoming water and its required volume:
- If the water supply is of high quality, but you want to make it even better, then jug filters are suitable for consumption less than 200 liters per month.
- With twice the consumption for water of medium purity and hardness, Trio is suitable.
- For hard water with a consumption of over 500 liters per month, Crystal is suitable.
For very dirty water, you need to use main filters and reverse osmosis purification.
Replacing the membrane and cartridges
Besides the Aquaphor OSMO-50 installation (version 5)? it is necessary to consider the procedure for replacing the membrane. To do this, you need to disconnect the JG tube from the fitting. Pull out the locking clip and press on the end of the plastic sleeve. This will allow the tube to be pulled out.
The membrane body can be removed from the seat. You need to grab it and pull it up with force. Next, the housing cover is unscrewed. The new membrane is removed from the packaging. It is installed in place of the old filtration element. The wide ring of the seal must be located on the threaded part of the housing. The membrane is pressed with sufficient force so that it takes the correct position inside.
You need to check the integrity of the seal, and then screw the cover onto the body. It is installed in its original position.
Next, the end of the tube must be moistened with water, as during installation, and inserted into the fitting until it stops. It is worth noting that during the initial installation of the system you do not need to install cartridges or a membrane. All filter elements are already in place.
Replacing Aquaphor OSMO-50 cartridges (version 5) is even easier. The kit includes a special key that is used to unscrew the flasks. First, the water is turned off and the tap on the sink is opened. If you do not relieve the pressure, it will be difficult to unscrew the flask. Old cartridges are carefully removed from their seats. Filters must be washed thoroughly. You need to install new replacement cartridges. Then the flasks are easily screwed in, and the system can be used again.
FAQ
I don't know what filter model I have, DWM-101 or DWM-101S. How to determine the model and choose the right new membrane? You have a DWM-101S filter (top membrane drainage) if:
- your filter serial number is 114,992 or greater, and the production date is later than 12/21/15.
- Your filter has a K-50S membrane installed: in the upper part of this module it is painted black (“cap”), in the lower part of the K-50S module there is no hole for the drainage tube.
Where can I find the official instructions for Aquaphor Morion DWM-101S? On the Aquaphor website: “Operation manual for Aquaphor Morion DWM-101S.”
Flushing the system
After installing or replacing the Aquaphor OSMO-50 filters (version 5), you need to flush the system. This will prevent coal dust from getting onto the membrane. To do this, you also need to use the instructions that come with the kit. First, turn off the water and open the tap on the kitchen sink.
Then you need to disconnect the JG tube from the pre-cleaner cartridge unit. To do this, the locking clip is taken out of the sleeve, pressed on the end and the tube is pulled out. It must be disconnected from the storage tank and then connected to the outlet fitting of the block with three cartridges.
The end of the tube is moistened with water and inserted into the seat until it stops. The liquid must be drained through the purified water tap. The procedure is carried out within 15 minutes. To do this, open the previously blocked flow of tap water. After this procedure, the tap is closed and the system is shut off again.
The JG tube is disconnected from the unit containing the three pre-cleaner cartridges. She is again brought to the storage tank. It is secured using locking clips. Next, the membrane is installed. If you do not follow this procedure, it will become clogged with coal dust. As a result, the throughput of the system and its cleaning properties will be minimal. The membrane will need to be changed.
Connection instructions
Installation of osmotic models requires professionalism. It is better to invite a specialist for this. If this is not possible, but you have experience in carrying out such work, you can do the installation yourself, following the instructions and connection diagram :
- First of all, you should decide on the location of the device.
- It is important to pay attention to the fact that there are no heating devices or pipes near the filter.
- Then you need to turn off the water supply and release all the contents from the tap.
- First, you can install the faucet on the side of the sink.
- Then you need to cut into the pipeline and install a triple adapter.
- After this, you can install the drain outlet. First, a clamp is installed on the drain pipe above the siphon. Then a hole in the pipe is drilled through the fitting and the outlet hose is inserted there.
- At the final stage, install the filter housing, the tank, if it is not built in, connect all the hoses.
Below you can see the connection diagram:
The manufacturer has simplified the master’s task as much as possible. All hoses included are painted in different colors. The instructions very simply describe the purpose of each hose. Carefully following the directions will lead to success.
After checking the tightness of the connections, the filter complex must be thoroughly rinsed until the tank is completely filled . Then release all the water and begin operation.
Starting the system
It is important to start reverse osmosis correctly. The inlet valve should be opened. It is necessary to inspect the system for leaks. All joints and threaded connections are carefully inspected. If drops of water are visible, you need to tighten the bolts and other connections more. But you can’t be too zealous, as you can break the thread.
The faucet handle for clean water must be opened. After some time, the filtered liquid will begin to drip. Then you need to wait 40 minutes. After this, the tap is closed. You should wait approximately 1.5 more hours. During this time, the storage tank will fill. The duration of this process depends on the characteristics of the membrane filter.
When the tank is completely filled, you need to completely drain the liquid from it. When the water flow weakens, you can close the tap. It is highly not recommended to drink water that the system would have filtered the first and second time. The procedure is repeated again.
Only after the third filling of the tank with water can it be drunk and used for cooking.
During the first week, you should periodically check the system for leaks. When it first starts, reverse osmosis can filter water that appears milky. It contains many air bubbles. They are forced out of the system during operation. Over time, the water will acquire its normal color and become transparent. The presence of air does not reduce the quality of the purified liquid.
Replacing the carbon filter and mineralizer
To replace the carbon filter, which is installed after the membrane, the water is turned off. By opening the tap for clean water, you need to relieve the pressure. The JG tube is disconnected. Then you can dismantle the post filter by removing it from the holder. To do this, you need to forcefully pull the cartridge up. The new post-filter is installed in the seat in the reverse order.
To replace the mineralizer, perform the same steps. The water is shut off, the tube is disconnected from the cartridge, which requires replacement. The mineralizer must be pulled upward with force. A new cartridge is installed in its place. The steps to connect all elements of the system are performed in reverse order.
